FEF322CASF Frigidaire Range - Instructions

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

I follow the video on your site

Screw the handle, that it...

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Removed rear panal, removed screws from of switch. Unplued wires and installed new switch and put back together. Very easy.

Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test

just put in slot

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.

I looked up the model number of the Tappan oven on the net, found the part on the PartSelect site, ordered it and it arrived within a few days. The disassembly should have required nothing more than a Phillips head screw driver, unfortunately one of the screws was completely frozen and I managed to strip the Phillips head socket.

The screw was in a very awkward position so I first tried using grip pliers on the edge of the screw - this failed, I then tried grinding a flat spot on either side of the screw circumference and using the flats for gripping - it worked but the screw wouldn't move. Finally, I took a hacksaw blade and cut a slot in the head of the screw. I widened the slot using miniature files and finally made the slot wide enough for a large slot blade screwdriver - this worked. After removing that one screw and maneuvering the broken hinge out of the access hole on the stove front (the break in the hinge was such that this took awhile) the rest of the repair went very quickly.

The oven door was such that I could not see all of the hinge and when the part arrived from PartSelect I thought it was the wrong part. I called your parts return number to ask some questions. The lady who took my call was extremely helpful and we first discussed the part ID, then she showed me how to find a picture of the actual part on your site. After looking at the picture and the diagram I suddenly realized the part was correct - it was just that I thought it was supposed to be installed in a different manner. I'm sorry I didn't remember to get her name because she certainly should be commended for he patience and her assistance. Thanks Again.