FEC36S8HSB Frigidaire Cooktop - Overview
Sections of the FEC36S8HSB
[Viewing 4 of 4]
Keep searches simple, eg. "belt" or "pump".
Screw
PartSelect #: PS461124
Manufacturer #: 5303288565
This is an authentic mounting screw, which works with ranges, wall ovens, cooktops and warming drawers.
$8.60
In Stock
Radiant Surface Element - Dual 1000W/2000W
PartSelect #: PS1145873
Manufacturer #: 318198923
No Longer Available
Dual Burner Element with Limiter - 8 Inch
PartSelect #: PS437628
Manufacturer #: 316049706
No Longer Available
Surface Burner Switch - 6" Warmer
PartSelect #: PS442608
Manufacturer #: 318078801
No Longer Available
Manuals & Care Guides for FEC36S8HSB
Click to downloadInstall
Installation Instructions
(0.39MB)
Specs
Product Specifications Sheet
(0.03MB)
Wiring
Wiring Diagram
(0.27MB)
Common Symptoms of the FEC36S8HSB
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dual radiant burner kaput.
Removed trim screws,(4) , lifted range top and removed the element after taking a picture of same. then disconnected the wires. I was upset because the new element had a different wire configuration. I put it in anyway in spite of your warning of not being able to return it if it didn't work. I fired it up and it did not work correct
... Read more
ly. After a couple of "...oh dear me." A few Hail Mary's and an educated guess I reversed two wires and gave it another smoke test. Well, kiss my ....! It works.
Read less
Parts Used:
-
Michael from Spokjane Valley, AL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
11 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner eye would only produce High Heat on all settings
Ordered a new Surface Burner Switch to replace the failed unit.
When I opened the burner lid, I could see the insulation on all the wiring for the burners had fallen apart and wiring was exposed. The wiring for all 4 burners was exposed as the insulation had deteriorated and fallen off over 80% of the circuits. It was just blind luc ... Read more k there was not a fire or an electrical failure on a grand scale. I replaced the wiring and burner connection assemblies as they also showed signs of age and deterioration.
Had the switch not gone bad, forcing me to look into the wiring assemble, there very likely would have been an electrical fire. In a 220 volt appliance, electrical fires are a lot more excitement than I need.
Scot Hooper
Keller Texas
When I opened the burner lid, I could see the insulation on all the wiring for the burners had fallen apart and wiring was exposed. The wiring for all 4 burners was exposed as the insulation had deteriorated and fallen off over 80% of the circuits. It was just blind luc ... Read more k there was not a fire or an electrical failure on a grand scale. I replaced the wiring and burner connection assemblies as they also showed signs of age and deterioration.
Had the switch not gone bad, forcing me to look into the wiring assemble, there very likely would have been an electrical fire. In a 220 volt appliance, electrical fires are a lot more excitement than I need.
Scot Hooper
Keller Texas
Read less
Parts Used:
-
scot from keller, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
9 of 28 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!