Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Top Broiler element burned out
I disconnected power cord. Removed cooking racks. Removed element mounting screws. Removed back panel and removed wires on both ends. Pulled element out put new one in and bolted down. Reconnected wires. Put rear cover on. Plugged in and checked for correct opreation. OK!
Your online instructions said to remove the two screws and pull out the heating element about 3 inches and disconnect. When I did this the element came out but not where it was connect to the wire., I could not locate the wire from the front of the oven. I then pulled out the oven from the built in cabinet and removed the rear panel. Then inserted the element with the 2 screws from the front and connect the wires to the element from the back of the oven. Jim
Turn off the breaker to the stove. Very important because when you move the control panel around after removing it, you can inadvertently touch a hot wire to a grounded metal part on the stove. Remove the 3 nuts from the back of the control panel and the two nuts from under neath the control panel on either far side. Pull the control knob off by pulling straight away from the control panel. Remove the switch by unscrewing the two screws. Match the 5 wires from the old switch to the new switch by removing one at a time and paying attention to the labeling of each on both switches. Reassemble in reverse order. Turn breaker back on.
I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act fast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.
took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.
Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. The biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...
My bake element (lower element) just about caught fire and needed replacing
The repair was straight forward and the video was a big help. I removed the oven racks and then used a 1/4" socket with a nut driver to unscrew the bolts at the back. Since this is a really old oven, the connecting wires were a bit difficult to remove from the bake element connectors. They seems kind of stuck, so I took a small, thin screw driver and pried up one of the metal clamps of the connecting wire just enough to let me budge the connector to detach the bake element. Had to do that for both sides. Then I just put the new bake element in, attached the wire connectors, made sure the wires and the ends of the bake element were all the way back in their holes, screwed the screws back in, and then put the racks back in. It was really easy, except for the bit of a challenge getting the wire connectors detached from the old bake element connectors. Works now without catching fire. :-D
From learning the hard way on a previous repair, I opened the circuit breaker for the oven at the circuit box (arc welders use 220 volts also). Then using a nut driver, I removed the two retaining screws and pulled the bake element from the oven (about 3"). Then I removed the spade connectors on both ends of the element and reconnected them to the new element. Then I gently pushed the element back into the rear wall of the oven and replaced the retaining screws. This procedure is extreamly easy and very straight forward, anyone could accomplish this task.
I removed the screws holding the element in place, pulled the element out, and one of the leads came off and dropped into the oven. I had to take the back of the stove off and feed the lead back through the hole into the oven. If I had been careful to keep the leads from dropping out of the hole, the whole repair would have taken only a few minutes. But even so, it was quite easy.
TURN BREAKER TO RANGE OFF! Move range out to access rear of the unit. Remove 6 screws to gain access to rear of controls panel. Pull knob off switch. Remove 2 pan head Phillips screws to take switch out. Lugs not in matching pattern but are clearly labled, swap wires one at a time. Reverse the disassembly steps and push the range back in place. DONE
Went to use the stove and the main baking element had a melt down.
shut off power to stove. Opened the oven door, removed the racks. removed 2 screws holding the element in place. gently pulled element out to expose connections. removed connections. discard old element. reattach connections to new element and reinstall. very simple.
i first replaced element after old smoked & quit. replaced switch but i noticed when i started to replace the wires one at a time something didn't seem right. after checking the #s on the old one, they didn't match up with the new one.luckily i had the stove diagram from a packet on the back of the stove. i traced each wire according to the diagram and everything worked out fine. i'm just glad i didn't replace each wire to wire.the #'s were on the switch where each wire went which was different than the org. even though they looked the same.