FC350 (Type 1) Porter Cable Nailer - Parts

This unthreaded trigger valve assembly is a genuine OEM assembly used in nailers. It includes the trigger valve, 1 rubber washer, and 3 roll pins. The trigger valve controls the flow of air in the tool which drives the piston and creates the nailing action. If the valve becomes stuck, the seals wear down, or the trigger breaks the nailer ...Read morewill leak air, struggle to fire, or not fire at all. Begin the repair by switching off the tool and using a push pin to remove the trigger. Remove the roll pins that secure the trigger valve and pull the trigger valve out of the housing. Insert the new valve into the housing, install the pins to hold it in place, and secure the stay pin with the washer.

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Porter Cable nailers and staplers. It helps to provide an air-tight seal between connected components, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are specified by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common among power tools are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. The...Read morese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common are: • Extrusion and Nibbling - O-ring has ragged, tattered edges. These are com...Read moremonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

An authentic OEM sourced replacement part which is specially designed for use with Porter Cable nailers and staplers. The purpose of this part is to provide an air-tight seal between components, over time it may wear out and begin to crack eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

This is a high-quality part which is supplied by the original manufacturer. It is specially made for use with Porter Cable nailers. It helps to provide a tight seal for the head valve. Over time it may wear out and begin to crack eventually requiring a replacement. For the exact location and the correct installation, please refer to the a...Read moreppropriate diagrams of your model. This high-quality part is made of durable rubber material and is sold individually. You will need a screwdriver and a wrench set to take the tool apart and perform the repair.

This is a genuine OEM replacement part used for Porter Cable nailers/framers. An O-ring is a flexible circle. It is used to maintain high pressures by creating a tight seal between rigid parts. This O-ring fits around the cylinder. Please be sure that this is correct ring for your needs, as there are multiple types/sizes used throughout. Sold individually.

This is a Genuine OEM replacement part used on a variety of Power Tools. It allows to keep the Carrying Case closed. This part is made out of Plastic and it is Sold Individually. Included in part number 901023

This is an authentic OEM sourced component which is specially designed for Porter Cable staplers and nailers. It is an identical replacement for a missing or faulty rolled pin that was originally installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardw...Read moreare. Keep in mind this high-quality item is made of durable metal and is sold individually.