F5108L0 Roper Range - Instructions

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

Replaced with the new burner works like new. Thanks a bunch!

Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!

Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.

I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked ... Read more . Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.

I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.

The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out ... Read more at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.

I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.

I have reinstalled the earlier unit.

Is part# PS 11744446 no longer available?



James E Weimholt. [email protected]

Lifted range top, disconnected and labled wires from old switch, removed old switch, replaced wires on new switch, installed new switch.
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch ... Read more on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!

1. Remove bottom drawer.
2. Remove spring (easier to take off bottom first).
3. Remove broken hinge.
4. Insert new hinge into oven door.
5. Insert hinge into oven.
6. Reattach spring.

I first tripped the power circuit breaker. Then I unplugged and removed the old element. Removing one screw allowed me to remove and replace the mounting clip. This did result in breaking off a small piece of plastic-like material from the electrical housing to which the clip was attached but did not hinder the replacement of the new ... Read more clip. I inserted the new burner element. The surface burner is now working fine.

Removed block (1 screw) Cut 2 connecting wires. Strip insulation. Attach new block with wire nut(per enclosed instructions) Heat shrink wrap with Lighter. attach block. 10 minutes: problem solved

Remove broken right hinge (3 screws)and detach spring. Replace right hinge and attach spring. Tip when ordering: make sure that you pay attention to which hinge you order (right hinge vs. left hinge). They are different, and when you order, the site does not do a good job of explaining which part number is the right hinge and which part n ... Read more umber is the left hinge.

removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy a ... Read more nd quick repair

Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.