EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

F22CWF3 Frigidaire Freezer - Instructions

All Instructions for the F22CWF3
46 - 60 of 86

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fridge was getting warm while the freezer was cold and running constantly.
0 of 2 people found this instruction helpful.
  • Jeremiah from Northglenn, CO
  • Easy
  • Less than 15 mins
  • Nutdriver
After testing and eliminating the temperature control and the timer as the problem, I turned to the thermostat. I had to wait for the ice buildup to thaw and then could remove the rear freezer panel (this was the 3rd time: first, to discover the ice buildup causing the problem, second when it came back after a complete thaw and test the thermostat, and this time to put the Partselect thermostat back in). My thermostat was visibly damaged from water melting into ice and expanding the casing and eventually breaking one of the connections. I connected the thermostat connection wires (not recommended) to get by while ordering the part, which shipped faster than local repair places could get it from their warehouses, and at a fraction of the cost. I'm really impressed with partselect's fast service and all the knowledgable customers who have explained how they installed them. I now have an intimate knowledge of how my fridge works and saved hundreds in repair, or twice that in replacement. Thanks!
Was this helpful?
Thank you for voting!
The new motor mount screw holes were not threaded.
1 of 5 people found this instruction helpful.
  • Greg from henrico, VA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this helpful?
Thank you for voting!
Freezer was building up ice. Running constantly.
0 of 3 people found this instruction helpful.
  • eugene from norwalk, CT
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Parts Select is an excellent source for help and parts identification. I highly recomend them.
My first option was to replace the defrost timer.
After still getting ice and frost buildup in freezer I decided to replace the defrost thermostat.
Remove all shelves. Losen icemaker if applicable. Remove light cover and bulb. R emove all screws securing rear vertical cover. Carefully move back panel, disconnect icemaker and bulb assembly. carefully remove styrofoam cover at upper left and remove defrost thermostat. I tested the thermostat and found it was defective. It would not close circuit after being placed in a working freezer. Reverse procedure to replace thermostat.
This solved the problem
Was this helpful?
Thank you for voting!
No problems
2 of 9 people found this instruction helpful.
  • Nancy from LEHIGH ACRES, FL
  • Really Easy
  • 15 - 30 mins
  • Wrench (Adjustable)
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this helpful?
Thank you for voting!
thermostate stop working frozzen up
  • Augusto from Gretna, LA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
just like the video show sa 1,2,3 yeaaa thanks
Was this helpful?
Thank you for voting!
coils would freeze over not allowing air to circulate throughout freezer
  • robert from royal oaks, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
replace thermostat and timer after defrosting and cleaning out freezer. I took less than 10 minutes and now freezer has a defrost cycle that eliminates frost buildup on the coils.
Was this helpful?
Thank you for voting!
Side rail for sliding shelf would not stay tight
  • Scott J from Westminster, CO
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered t wo nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.
Was this helpful?
Thank you for voting!
Freezer would constantly run. Even when it was super cold inside.
  • David from San Marcos, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I ordered a new thermostat and installed it in less than 15 minutes. Looks like the problem is fixed. Now ,the freezer cycles on and off correctly. The part was ordered on a Monday and I got it the next day. I am very satisfied.
Was this helpful?
Thank you for voting!
door switch broke
  • Ricardo from VICTORVILLE, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed bottom cover , just two screws , slid old part through install hole and removed wires from old switch and installed on new switch. Installed new switch in same hole and pushed gently until it locked in place. Reinstalled bottom cover and done.
Was this helpful?
Thank you for voting!
Temp skyrocketed
  • Wayne from Chatham, IL
  • Really Easy
  • Less than 15 mins
Took out three shelves. Removed 9 screws with a battery powered drill with a phillip screwdriver bit. Popped off the thermostat like I had seen on the video. Put the new thermostat on. Replaced the two wires one at a time. Reassembled the unit. This was so quick that my wife told me to let her know when I wanted to fix the freezer. She wa s shocked that I had completed the job. I'd been in the garage less than 10 minutes. It has been six weeks. and the freezer is working perfectly.
Was this helpful?
Thank you for voting!
Freezer ran alot, then temperture began to vary.
  • John from Port Republic, VA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Watched video on Part Select which shows you how to replace the thermostat with several good pointers. Very easily done and now the freezer works great.
Was this helpful?
Thank you for voting!
broken light switch
  • John W from Gloucester, MA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed 2 screws holding front bottom vent grille. . Through opening behind grille found broken part of switch hanging on wires. Removed wires from switch and fed them out through hole for mounting switch, connected wire and pushed into place. The greatest difficulty encountered was my 82 year old knees.
Was this helpful?
Thank you for voting!
Freezer would not keep running and the temperature was too warm.
  • Edmond from Carroll, NH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Followed the sites instructions. Empty the bottom part of the freezer. Remove the screws. Move the panel out of the way. Easily remove the old part and replace with the new. Put the panel and screws back in place. The freezer works.
Was this helpful?
Thank you for voting!
Fan would not start occasionally
  • Mike from Satellite Beach, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers
I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer . Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.
Was this helpful?
Thank you for voting!
Evaporator Fan Motor was making loud rattling sound.
  • Richard from Clovis, NM
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplugged freezer from electrical socket. Removed lower trays from freezer. Removed sound proof stripping from sides of back panel. Removed upper, lower and side screws from back, lower panel using No. 2 phillips screwdriver. Disconnected motor wires from quick disconnect power supply. Removed motor bracket from freezer back using nut dri ver. Removed motor from bracket using same nut driver. Replaced motor and screws in bracket. reattached quick disconnect. Attached fan blade to motor making certain to push blade on shaft securely. Replaced bracket to freezer back. Replaced back cover. Replaced stripping. Plugged into power supply. Total time 15-20 minutes.
Was this helpful?
Thank you for voting!
All Instructions for the F22CWF3
46 - 60 of 86