EZ2500A Honda Generator - Parts

This is a genuine replacement part which is supplied by the original equipment manufacturer. It is specially designed for use with Honda engines commonly installed on a variety of lawn and garden equipment. The purpose of it is to filter out dirt and other debris from the fuel that is supplied to the engine. It will over time become clogg...Read moreed and restrict the fuel from getting to the carburetor so it will need to be replaced. It is made of a high-quality plastic and is sold individually. Check the diagrams of your model for the correct installation of the new part.

This is an authentic manufacturer sourced replacement part designed for use with Honda engines. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This item has been sourced from the original manufacturer, and it is intended to be used with small engines from Honda. The metal spring links with the starter pulley and is used to recoil the roper back around the pulley after the rope is pulled. This item is available as an individual replacement part.

This is an authentic item that is supplied by the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. Please make sure to check the appropriate diagrams of your specific model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

This is an OEM Sourced replacement part used on Honda Engines. This Filter is made out of Paper, Foam and Metal. This item is Sold Individually. Its purpose is to filter out dust and debris from contaminating the engine. To replace this you would need a Wrench to remove the Air Cleaner Cover.

This is a genuine replacement part manufactured for Honda small engines. Replacing carburetor gaskets is recommended when repairing or rebuilding carburetors to ensure proper seals. This gasket set is compatible with several engine model types, and is sold as an individual set.

This part is a genuine OEM item that has been sourced to be used with Honda small engines. This spacer is used as a link between the carburetor and the air cleaner elbow. The carburetor spacer is priced as an individual part, please note associative parts are available separately.

The noise suppressor cap assembly, also known as the spark plug cap/boot is responsible for connecting the spark plug to the ignition coil, and helping to reduce the amount of noise created when running outdoor power equipment. This OEM replacement part includes a rubber cap with a metal contact inside. It is found at the end of the spark...Read more plug wire and has a threaded center shaft which allows you to easily screw it into position. Over time the metal contact may corrode, or the cap may dry out and crack or break. If your equipment is misfiring, running poorly, or has interference with other electronic equipment, the cap assembly likely needs to be replaced. To remove the old cap assembly, use your fingers or a set of pliers to carefully pull it off the end of the wire. Place the new cap assembly onto the end of the wire and fasten it securely. Please note this part is sold individually.

It is a genuine OEM sourced replacement spark plug which is used with Honda engines commonly installed on lawn and garden equipment. A spark plug is used to deliver electric current from an ignition system to an internal combustion engine. Over time spark plugs tend to wear out, become dirty or fouled eventually requiring a replacement t...Read moreo maintain peak performance. You should gap your spark plug according to the owners manual of the outdoor product you have. This high-quality component is sold individually, please note you would need a spark plug wrench or a socket wrench to install/remove a spark plug.

This item is an authentic Honda replacement part that has been sourced from the original manufacturer to be used with small engines. The gasket is used to seal the connection between the carburetor insulator and the cylinder's intake. This item is available as an individual replacement part.