EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

EX210SE5021 Subaru Engine - Parts

13 - 24 of 208

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Gasket – Part Number: 277-16001-23
No Longer Available
Gasket
Part #277-16001-23
This authentic manufacturer-sourced gasket is designed for use with Subaru / Robin engines commonly found in lawn and garden equipment. It serves as a carburetor gasket, providing an air-tight seal for the rocker cover to ensure proper engine performance. Made from high-quality composite material, this gasket is built for durability but may deteriorate over time due to heat and wear, requiring replacement. It is sold individually, and for correct application and installation, users should refer to the owner’s manual and model-specific diagrams.
Gasket – Part Number: 021-11400-20
No Longer Available
Gasket
Part #021-11400-20
This gasket, also known as the oil drain plug gasket, is a ring-shaped, metal component used in outdoor power engines. It is supplied by the manufacturer and can be found at the bottom of the engine oil pan where the drain plug is installed. The gasket is responsible for sealing the area between the oil drain plug and the engine block to prevent oil from leaking during oil changes. Over time the gasket can wear down, corrode, or crack. If the gasket can no longer seal the area, oil will escape from the oil pan, leading to inadequate lubrication, increased friction, and engine damage. Before you begin the repair, drain the oil from the engine to prevent contamination. Use a wrench to loosen and remove the oil drain plug. Peel off the old gasket, and thoroughly clean the drain plug and oil pan surface. Install the new gasket and ensure that it sits firmly on the oil pan. Finally, reinstall the drain plug, and be careful to avoid overtightening it.
Oil Seal – Part Number: 044-02502-10
No Longer Available
Oil Seal
Part #044-02502-10
This is an authentic Subaru/Robin replacement part that has been sourced from the original manufacturer to be used with small engines. The oil seal is used to seal the area around the crankshaft where it exits the crankcase. This item is available as an individual replacement part, please see illustrated diagram for associative parts.
Governor Gear Cp – Part Number: 277-45004-K1
No Longer Available
Governor Gear Cp
Part #277-45004-K1
This is an authentic item that is supplied directly from the original equipment manufacturer for use with Subaru/Robin engines commonly installed on lawn and garden equipment. It is an identical replacement for a missing or a damaged governor gear cp that was installed on a new unit, please make sure to refer to the diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality component is made of durable plastic and is sold individually.
Governor Shaft – Part Number: 277-42201-33
No Longer Available
Governor Shaft
Part #277-42201-33
The governor shaft attaches to the governor lever and is made of metal. It is available as an individual replacement part. This genuine item is supplied by the original equipment manufacturer for use with Subaru and Robin engines. A wrench might be helpful during the installation of this part. This item may become bent or broken and will need to be replaced.
Fuel Filter – Part Number: X64-13600-10
No Longer Available
Fuel Filter
Part #X64-13600-10
This is an authentic Subaru/Robin replacement part manufactured for use with small engines. The fuel filter fits in the fuel tank just under the cap. This fuel filter strains the fuel as it is poured into the tank. The fuel filter is sold individually.
Packing – Part Number: 214-62450-08
$5.28
In Stock
Packing
Part #214-62450-08
It is a genuine OEM component which is specially produced for use with a Subaru / Robin engines that are commonly installed on a variety of lawn and garden equipment. This replacement part provides a tight seal for the float chamber body. Unfortunately, over time the material may wear out or get damaged eventually requiring a replacement. Please make sure to check appropriate diagrams of your model for the correct application. It is made of a durable material and is sold individually. You will need a wrench to remove and resecure the bolt that secures it to the float chamber body.
Packing – Part Number: 277-62110-18
No Longer Available
Packing
Part #277-62110-18
This is an authentic OEM part directly sourced from the Subaru / Robin manufacturer. The plastic packing is compatible with many small engines. This item secures the cup to the cock body-a within the carburetor. This part is sold individually. A screwdriver is helpful in making the repair. Please refer to specific manual and diagrams for instructions.
Governor Spring – Part Number: 277-42510-23
$6.69
In Stock
Governor Spring
Part #277-42510-23
Gasket2(insulator) – Part Number: 20A-35903-03
No Longer Available
Gasket2(insulator)
Part #20A-35903-03
This is an authentic OEM sourced replacement part used on a variety of Subaru/Robin engines. This part provides an air tight seal between a carburetor and an insulator. This part is made out of composite material and it is sold individually. You would need a wrench to complete a repair.
Governor Sleeve – Part Number: 277-41902-01
No Longer Available
Governor Sleeve
Part #277-41902-01
This is a genuine Subaru and Robin replacement part for use in engines. The governor sleeve attaches to the governor gear. A hammer may be needed during the replacement of this part. It is made out of metal and will need to be replaced if it breaks. This item is sold individually.
Governor Lever – Part Number: 277-42301-40
No Longer Available
Governor Lever
Part #277-42301-40
This is an authentic OEM sourced item which is specially produced for use with Subaru and Robin engines. The governor lever attaches to the governor rod. It may require a wrench during installation. This part is made out of metal and will need to be replaced if it bends or breaks. Keep in mind that this high-quality part is sold individually.
13 - 24 of 208