EW30SO60QSA Electrolux Microwave - Instructions

I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.

was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a ... Read more 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .

After unplugging the unit remove the control face buy removing the screws. All three door switchs are on a bracket on the left. Remove the two screws holding the bracket in place and pull out. Disconnect the wires from the three switches and test each switch indivually to determine the bad one. I used a multimeter set on ohms.Replace the ... Read more bad switch with the new one and replace all the wires. Reassemble the unit and you are good to go.

It is a undercabinet stovetop microwave. First had to take it down and unplug. Remove the top cover locate the door switch. Used neednose pliers to remove switch. Unplug two terminals.Plug new switch and use pliers to replace back @ same position.Plug in socket temporarily to see if it works.Afterwards if it works.Unplug and replace cover ... Read more .Ready to be replaced back under cabinet.

Remove trim strip around glass on inside of microwave door to expose screws, remove all the screws, front of door will come off, remove and replace broken latch re-attach spring,re-position front door replace screws and trim

Removed microwave cover trim,
removed the microwave#1philips and security screws , removed the cover. Removed the 3 #1 screws holding the racket in front of the light bulb. I pryed the plastic clip holding the light, removed the bulb put the new bulb in and reversed the order to reassemble

I took off the keypad panel,then plugged it back in,turned it on for 2 seconds so I can see where the spark was comming from,saw it was the capacitor, unpluged it while it was on so the voltage would drain,took out the capacitor ordered it a few days later,put it back in, now the wife is happy,and when she is happy,I'm happy :-)

This is an OTR microwave oven, needs to be removed to diagnose problem. I did not diagnose problem properly, I searched online for possible causes, read that (99%)percent of the time the interlock switch was bad and replacement should solve my problem. It was also stated to be an easy fix,15- 45 minutes depending on ability. I ordered the ... Read more relay switch. Took the oven down then removed outer shell. With my multimeter I began to test, fuses(2), interlock switches(3)and transformer. 3 interlock switches were ok, fuses were fine, and had power to the transformer, meter could not read output of transformer because of high voltage, (2300v). I'm down to magnetron (about a hundred bucks) or the touch pad/ circuit board. I have a countertop micro that I'm putting in place of the OTR. As far as Partselect, my item was shipped and delivered on time, instructions for changing that part was quite accurate. Would order from here again, just do my homework first.

I have a Kenmore elite built-in microwave. I started by opening the microwave and removing the small trim frame from the rectangle surrounding the window which covers the screws needed to be removed as part of latch head install process. But then went and removed every other screw from the frame which holds the door onto the hinge bracke ... Read more t. It is important not to remove all of the screws because the door will fall off the frame and shatter on the floor. My particular microwave when the door is open is right about 32 inches off the ground. I found two kitchen chairs that were about 32 inches high on the backs and positioned them where they supported the door when it was open and horizontal. Once I did this, I was able to unscrew the remainder of the screws, holding the door on the frame and slowly released it while holding onto the door frame, so it did not slam – it is spring loaded. I moved the door to another location and moved to replace the latch head on the upper right side by removing the broken latch, head retaining spring with a small pair of pliers and leaving it hanging on the door anchor, and then using a Philips screwdriver to take the broken latch off. I basically repeated these procedures in reverse, putting the new latch head on, connecting the spring, and then supporting the door frame with the chairs holding it just high enough to lower the hinge frame and line up to screw holes so I could start putting the screws back in. When I was done, I inserted the window frame insert cover over the screws and tested the microwave. It worked flawlessly.

I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.

Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.

Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch

I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply ... Read more on my ice maker.