EW30EW55PSC Electrolux Wall Oven - Parts

Terminal block kits are also known as terminal boards, or terminal strips, and they are found in a wide variety of household appliances. Most often in ranges, wall ovens, and dryers. This kit attaches the power cord to the inner wiring of your appliance. If the terminal block is faulty, your appliance will not get the power it needs to op...Read moreerate properly. When removing the old block pay close attention to the wire placement, this will make installing your new part much easier. If you notice any of the wires or wire terminals are corroded or damaged they will also need to be replaced.

The temperature sensor, also known as an oven probe, helps measure the temperature within the oven cavity. If your oven is too hot, not heating evenly, has little to no heat when baking, or flashing F3/F4 error messages on your control board, you may need to replace this part. This part measures 6" long and is made of metal. Please make s...Read moreure to disconnect the power to your oven range before starting this repair. This temperature sensor is a genuine OEM part.

Sold Individually.

This authentic OEM high-limit thermostat, also known as a limit switch or cooling fan thermostat, serves as a safety feature to prevent the oven from overheating. It monitors the temperature inside the oven and activates the cooling fan when the temperature exceeds a certain limit. The cooling fan helps dissipate heat and maintain a safe ...Read moretemperature. The high-limit thermostat is usually situated inside the top panel. If the high-limit thermostat is broken or faulty, the cooling fan may fail to turn on, leading to excessive heat buildup inside the oven. You might also notice that your food cooks unevenly since the oven struggles to maintain the desired temperature. In some cases, if the high-limit thermostat is completely non-functional, the oven may not heat up at all. You can test the sensor at room temperature by measuring the resistance between the two prongs at the end of the sensor connector. The resistance should read approximately 1080 - 1090 ohms at room temperature. To access the thermostat, refer to your user guide for detailed instructions. Generally, you need to ensure the power is disconnected at the breaker, lift the top panel on its hinges, remove the screws on the plate under the burners, take out the burners and plate, disconnect the wires from the old thermostat, and remove the mounting screws to release it. Please note that the replacement part is sold separately from the cooling fan.

This convection fan blade is designed for use with various makes and models of range and oven and is sold as an individual part. Made of metal and measuring approximately 4.75-inches in diameter, this genuine OEM fan blade works with the convection motor to circulate and distribute heat evenly throughout the oven. If your oven is not gett...Read moreing hot enough or the heat is not circulating properly, or if the fan blade in your oven has become warped, damaged, or chipped, it needs to be replaced immediately. To replace the fan blade, disconnect your range from the power and locate the fan assembly. With the appropriate screwdriver and wrench, remove any assembly covers and the securing nut from the blade. Once the nut is removed, install the new blade and secure it and re-install the cover.

This hidden bake element is an essential heating component located beneath the oven floor panel, providing consistent heat for baking, roasting, and warming. Designed with a durable ceramic sheath to protect the heating coil, it ensures reliable performance and even temperature distribution. The element measures approximately 13 to 13.3 i...Read morenches in width and 11 inches in depth, making it a perfect fit for standard oven cavities. If your oven is producing little or no heat, baking unevenly, or showing visible damage such as cracks or blistering, replacing the bake element can restore optimal functionality. Installation is straightforward—simply disconnect power, remove the floor panel, and replace the element with the new one.

This fan blade retainer nut in your oven secures the fan blade onto the motor shaft, preventing it from coming loose during operation. You can typically find it at the back of your oven behind a cover. If you notice that the fan blade becomes wobbly or does not rotate smoothly, or your oven starts to make rattling or scraping sounds, the ...Read morenut may be damaged. If the fan blade cannot spin properly, your food may cook unevenly. Your oven will also work harder and consume more energy to maintain the desired temperature. To access the nut, you will need to remove the back panel of your oven. Remove any screws or release any clips holding it using a screwdriver. To remove the nut itself, you will need either a wrench or a pair of pliers to loosen it from the motor shaft. The fan blade is sold separately from this genuine OEM nut.

This replacement light bulb provides clear illumination to improve visibility during appliance operation. It is commonly replaced when the original bulb burns out, flickers, or no longer produces adequate light.

Experiencing problems with your refrigerator? We understand how crucial it is for you to have your refrigeration appliances running efficiently. That's why we bring you this genuine Blade, Fan Condenser, from Whirlpool?a trusted name in appliance components. The Fan Condenser Blade isn't just a spare part; it's the heart of your refriger...Read moreator's cooling process. By circulating air across the condenser coil, it cools the hot refrigerant before it reaches the evaporator, ensuring that your fridge operates smoothly and effectively. Please note, even though many parts look quite similar, they can have variations in size and shape. To get the best results, make sure this Fan Condenser Blade aligns perfectly with your specific Whirlpool refrigerator model. Before installing, remember to remove and safely store any food items. Once done, you'll have peace of mind knowing that your refrigerator is back at its best, capable of performing just like it's brand new. So, get ready to restore your refrigerator's performance using this essential Whirlpool Fan Condenser Blade. Made to provide reliability and optimum performance, it will make your appliance as efficient as the day you bought it.

This halogen lamp assembly in your oven illuminates the cavity and is often located near the back wall or on the ceiling, so that you can easily monitor the cooking progress of your food. It consists of a bulb and a protective cover. To check if it is broken, look for a burned-out or broken bulb, a cracked or missing cover, or loose conne...Read morections. If the bulb does not light up despite being functional, there may be an issue with the assembly. Not replacing a damaged assembly can make it difficult to check your food or identify heating or spillage issues, so prompt replacement is essential. To remove your lamp assembly, first turn off the oven and allow it to cool down to avoid burns or electrical shock. If there is a separate power switch for the lamp assembly, turn it off. Alternatively, switch off the power at the circuit breaker for complete safety. Consult your user guide to find the wire connection point for the lamp assembly. You may need to remove a small cover or access panel to access it. Carefully unplug or detach the wire from the oven. Once the wire is disconnected, you can remove the entire lamp assembly from its mounting location. This OEM replacement part comes with a covered bulb and a wire connector.