EW27EW55GS4 Electrolux Wall Oven - Instructions

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to mak ... Read more e sure all worked AND IT DID!

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the o ... Read more ven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as w ... Read more ell as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.

Remove two screws in back to release the top.
Lift the top from the back and pull backwards to remove.
Open washer door and unscrew two screws to release the switch.
Reach down inside from the front and remove the switch.
Unplug the switch and replace with the new one. Reverse the process to install.
I found it ea ... Read more sier to have someone hold the switch while I screwed it back in.

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

Moved the stove away from the wall, unhooked the electric cord and the gas pipe. In the oven, undid the two screws holding the probe. Removed two screws and removed the electrical cover panel from the stove back, disconnected the quick connect to the probe and pulled the probe from the oven. Reversding the proceedures, put the new probe ... Read more into the oven, hooked up the quick connect and replaced the electrical panel cover. From the front, reinstalled the probe with the two screws, reconnected the gas and the power cord and put the stove back into position. It works just fine now!

Removed 2 screws holding old temperature sensor inside the oven and gently pulled out the wire till the connector came through the hole. Disconnected old probe and attached new one. Fished the wire back in the hole and replaced the two screws. Then followed the operating instructions for calibrating the oven. Ended up setting it +5 deg ... Read more rees. So far, works great.

1. Moved stove from against the wall. 2. Unplugged the power supply. 3. Removed the electrical pannel cover. 4. Disconnected the quick connect probe plug. 5. Opened the oven and removed the probe. 6. Installed the new probe. 7. Connected the quick connect plug. 8. Reattached the electrical panel cover. 9. Plugged in the electrical suppl ... Read more y. 10. Moved the stove back into its original position. ****Note**** THIS IS THE SECOND TIME I REPLACED THE PROBE. THE FIRST REPLACEMENT LASTED ONLY 5 MONTHS!!!!

Disassemble oven door using diagram from website.