EW23BC71IB2 Electrolux Refrigerator - Instructions

SIMPLY REMOVE THE OLD GASKET PULLING LIGHTLY BY HAND
THEN PUSHING THE NEW GASKET BY HAND

Googled it on Youtube - unplugged the fridge, used a paint scraper to loosen the old light switch, unplugged it from the electrical source, connected the new switch, replaced the whole unit into the proper location and pushed it firmly into place.

After unplugging the fridge, I took a small flat headed screwdriver and carefully pried off the light switch from the inside, right side of the refrigerator. I disconnected the 2 wires from the switch and replaced it with the new switch and pushed it back into the frame of the fridge. Done !! Very very easy !! Thank you

Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse

Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves

Original unit had screw on lugs. After removing old unit, I unscrewed the lugs, cut the lines to remove the nuts and inserted them into the new unit. Everything was color coded so connection was simple. Reinstalled unit, cycled the ice maker several times only to discover the fill tube at in the freezer had frozen ice blocking the tray f ... Read more rom getting water. Used a hair dryer to thaw out the tube, water flowed instantly. Very easy repair.

I watched the video and followed every step as outlined. It worked perfect, until I reconnected the supply line to my triple water valve. I used the old compression fitting and the compression nut. I should have cut the line and installed a new fitting and nut. The water on the floor the next morning reminded me of that. So back out I wen ... Read more t and replaced the compression fitting and it has been as good as new. The ice maker took a few cycles to work again, I think it needed to fill the line with water first. But I have a huge sense of pride every time I hear water dispenced or ice dump in the freezer. Thanks for the help and encouragement!

Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still sh ... Read more ooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

Watched the video on your website and you can’t go wrong.
Thanks for being there
Mike

slide old filter out and insert new one

Straight forward repair. Remove the four screws holding cardboard back. Remove the 2 screws holding the valve. Unscrew the water lines and unplug the electrical connections. I would caution that it would be wise to either take a couple photos or write down the order of connection. Even though it is somewhat color coded and the water lines ... Read more are different sizes, a photo removes any confusion. My old valve had threaded connections using brass nuts and ferrules. The new valve has push in connections so you need to cut the ferrules off.. When cutting off the tubing, be sure to cut square. An angled or "squished" cut will leak when pushed into the fitting. Attach the valve to the refrigerator with 2 screws and replace the cardboard back and you're finished. While you have the back off is a good time to clean the coils. I left my fridge out and back off for a couple of ice making cycles so I could check for leaks (how I know the tubing needs to be cut very square). All in all, a very easy fix.

I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HO ... Read more LD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.

very easy, make sure to watch the provided you tube video.

After sending PartSelect the info to their troubleshooting dept. about my ice maker, they recommended replacing the ice solenoid. I did so at a cost of $102. No change, turned out replacing the ice maker(did not purchase from PartsSelect) was the issue and works fine now.

So wasted $102. FYI the part took 6 days to arri ... Read more ve.