EVP394 Caloric Microwave Oven Combo - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Front Burner Would Not Heat
2 of 2 people
found this instruction helpful.
-
GAIL from ORCHARD PARK, NY
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
I cut the power to the circuit. Removed the burner and then unscrewed the old aluminum plate attached to the range top cover. Opened the topcover to access the wires. I cut the two wires being sure that I left enough length. I then slipped the two new wires with the brass contacts into the new black plastic holder until it locked
... Read more
. Reattached the new metal plate to the range cover, fed the wires through and snapped the new plastic holder into the aluminum plate. Secured wire ends with the ceramic wire nuts. Total time about 30 minutes.
Read less
Was this helpful?
Thank you for voting!
Burner would not heat up.
2 of 2 people
found this instruction helpful.
-
Nancy from Baldwinsville, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 2 screws, cut the wires, pulled the part out that the element plugs into. Replaced the old part with the new one and put the screws back in to hold it, reconnected the wires and plugged in the element. Turned stove on and Valaaaa! It was fixed in 10 minutes! Thanks for the great repair parts!
Was this helpful?
Thank you for voting!
Broken glass tray
3 of 5 people
found this instruction helpful.
-
Jerry from Roseville, CA
- Really Easy
- Less than 15 mins
There was nothing to actually, I just put in the bottom of the oven and cooked my sausage about 40 seconds later there is a loud POP and that's it. End of repair, end of breakfast, end of oven. I am returning the glass tray to you and asking for a refund. It was less expensive to go buy a new oven then to have that 30 year old repaired
... Read more
!
I do thank you for you prompt service and shipping.
We can't say we didn't try.
I do thank you for you prompt service and shipping.
We can't say we didn't try.
Read less
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Screw hard to get off
2 of 2 people
found this instruction helpful.
-
Lawrence from BROOKSVILLE, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Drilled a pilot hole with a 1/16 th drill bit and tapped off screw head.
Was this helpful?
Thank you for voting!
burner inop
2 of 3 people
found this instruction helpful.
-
Donald from Milford, MI
- Easy
- Less than 15 mins
-
Screw drivers
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy a
... Read more
nd quick repair
Read less
Was this helpful?
Thank you for voting!
Missing oven rack
2 of 3 people
found this instruction helpful.
-
Denise from Pittsburgh, PA
- Really Easy
- Less than 15 mins
Although this was not a repair I wanted to let you know your service was outstanding and the price quite reasonable. I am very happy to finally have a much needed second rack in my oven that was not there when I purchased my home. Thank You
Was this helpful?
Thank you for voting!
N/A
1 person
found this instruction helpful.
-
Gerry from Mackay, ID
- Really Easy
- 15 - 30 mins
-
Screw drivers
I followed the instructions provided.
Was this helpful?
Thank you for voting!
Range oven door switch need replaced
1 person
found this instruction helpful.
-
Ruth from Gastonia, NC
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top;
... Read more
and close lid. Part #866294
Read less
Was this helpful?
Thank you for voting!
Sockets burnt out.
1 of 2 people
found this instruction helpful.
-
James from Bear, DE
- Really Easy
- 15 - 30 mins
-
Screw drivers
Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.
Will buy from Part Select Appliance again.
Was this helpful?
Thank you for voting!
wire came loose and shorted out
1 of 2 people
found this instruction helpful.
-
Elizabeth from HOUSTON, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this helpful?
Thank you for voting!
I snapped a bolt on the main power terminal block when connecting the pigtail.
3 of 8 people
found this instruction helpful.
-
Frank from Palm Coast, FL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver.
... Read more
Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Read less
Was this helpful?
Thank you for voting!
The three braces under the coils had weakened and fallen apart
2 of 5 people
found this instruction helpful.
-
Suzanne from COZAD, NE
- Very Easy
- Less than 15 mins
I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.
Was this helpful?
Thank you for voting!
Replace oven racks
2 of 5 people
found this instruction helpful.
-
Gregory from Davenport, IA
- Really Easy
- Less than 15 mins
Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!
Was this helpful?
Thank you for voting!
Stove Burner wouldn't heat up
1 of 2 people
found this instruction helpful.
-
Donna from Sandwich, MA
- Really Easy
- Less than 15 mins
Someone did the repair for me.
Was this helpful?
Thank you for voting!