EV200FXKQ04 Whirlpool Freezer - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

Remove lower door hinge only, and door pops out. Then lay door on floor and remove the screws fastening the inner freezer tray & gasket to the door; this is where the cordless drill w/nut driver attachment is handy as there are 30+ screws to remove and an open freezer with all your food gaining temperature. At this point drop the new gask ... Read more et in the dryer on low heat for 5-10 mins to soften it, regardless of it's condition. Have someone clean the sealing area on the freezer and where you have removed the old gasket on the door while you fit the new gasket in. Renew all rusted screws and smear a little grease on hinge for future protection since the door is off. Remount door and check for leaks, the door should close and seal on it's own WITHOUT pushing. This is where I realised the importance of warming the gasket, I got lucky by passing a blow dryer along the leaking areas with the door closed.
Point: When buying a new freezer look for compression of the gasket which is an indicator of a warped door. My freezer is only 5yrs old and I shouldn't be changing the gasket so soon!

Replaced the compressor with the new one I purchased from you. Installed new parts and recharged unit. The refrigerator / freezer is working better than new. Thanks for the great deal on the compressor. It was here in 3 days. All the parts fit exactly and had no difficulty in the installation or startup. The directions for the wirin ... Read more g were a great help also. Thanks again.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

Using a 3/8" wrench I took the top hinge off of the door. I had a friend around so I put him to work but the project could be done alone. We set the door on a countertop and began removing the old gasket with the nut driver on a cordless drill/screwgun. We eventually decided it was worth the extra effort to set the door on sawhorses in ... Read more the garage (where the freezer is located).

I had stored the new gasket in the garage before installation and wished I had brought it inside to warm it up first. I remembered reading posts about using a hair dryer to soften the gasket but forgot about the post about putting the gasket in the clothes dryer for a few minutes. Stretching the new gasket around the door while it was cold was tricky in some spots but doable. One or two of the the corners of the new gasket began to pull apart but not enough to compromise the seal - although for the price of the gasket, I would have rather this not happened. I wish I would have used the clothes dryer first. Instead, we simply threw in a few screws in places and stretched the gasket around the corners. This was one time I was especially glad to have another person around.

After negotiating the corners and replacing all of the screws, we quickly placed the door back on the bottom hinge and put the top hinge back on. It was again nice to have a friend help square up the door before tightening the top hinge. We used a hair dryer to soften the gasket and a lot of hand work to mold the gasket and close the gap beyween the door and the freezer. Again, I think the clothes dryer would have saved time here as well. The gasket was quite compressed and needed a lot of work to help it "open up" and make a good seal.

Good luck on your own repair!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

My seal around the freezer door was in need of changing. Placed the new seal in the dryer for about 10min while I removed all the screws from around the door. When I got to the bottom of the door the screws were rusty. Removed the old seal. Have back up screws on hand incase this happens. I cleaned the area at the bottom of the door that ... Read more had become rusty. Then draped the new seal over the top of the door and started screwing the new one to the door. It was done! Pretty quick and easy.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Used a screw driver to pull old switch. Pulled one wire at a time, only two wires. After wires instlled to new switch push new one back in place where the old one was.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Followed instructions including web. Soaked new gasket in HOT water. Took door off freezer and put it on horses. Two person job.

It was easy to take the door off by taking the two screws (located on the top of the freezer) off the top hinge and lift the door up off the bottom hinge. I took it outside and laid it on a table. Removed all the screws and took off the panel so I could remove the old gasket and clean the door and panel. The inside of the door was full of ... Read more ice so we removed that and the insulation which I replaced. My wife then put the new gasket in the dryer on medium temp for about 5 minutes. We slipped the new gasket on the panel and lined it up on the door and screwed it back on the door. Then we put it back onto the freezer bottom first then replaced two screws on top hinge. Shut the door and use a blow dryer on the gasket with the door closed to make the gasket seal / conform to the door/freezer until there are no gaps between the gasket and the freezer. Note: Once the ice and water are out of the door the door doesn't weigh nearly as much as it did. Also

Replaced the door gasket.

Loosen the two bolts for the door top hinge. Make them loose enough so you have room enough to lift the door off its bottom hinge. But befor you do that use a marker to trace around the top hinge location, makes it easy to set it back correctly.

Take the door and lay it down on the floor, I ... Read more used a coffe table to allow for the door handle.

Remove all the screws holding the seal on. Note: it’s likely the bottom screws are rusty so get some replacements before doing this job.

Remove old seal and fit the replacement. I installed the four corner screws first to get the seal aligned.

Install ALL screws before tightening, this aids seal alignment with the holes in the door.

Refit door.