EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

ETD646 Caloric Cooktop - Instructions

All Instructions for the ETD646
31 - 45 of 105

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
1 of 2 people found this instruction helpful.
  • Nicki from ELSIE, NE
  • Very Easy
  • Less than 15 mins
No problem Took off old ones and replaced with new.
Was this helpful?
Thank you for voting!
Drip pans needed to be replaced
1 of 2 people found this instruction helpful.
  • Mark from ROSENBERG, TX
  • Very Easy
  • Less than 15 mins
1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements
Was this helpful?
Thank you for voting!
Sockets burnt out.
1 of 2 people found this instruction helpful.
  • James from Bear, DE
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.
Was this helpful?
Thank you for voting!
Simple - needed to replace the drip pans on the stove between tenants in a rental apartment
1 of 2 people found this instruction helpful.
  • Tama from Pacific Grove, CA
  • Really Easy
  • Less than 15 mins
This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.
Was this helpful?
Thank you for voting!
Stove Burner wouldn't heat up
1 of 2 people found this instruction helpful.
  • Donna from Sandwich, MA
  • Really Easy
  • Less than 15 mins
Someone did the repair for me.
Was this helpful?
Thank you for voting!
Drip bowls very dirty and stained
1 of 2 people found this instruction helpful.
  • john from donna, TX
  • Really Easy
  • Less than 15 mins
Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering proces ses were simple and delivery was faster than I hed expected.
Thank you
Was this helpful?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
1 of 2 people found this instruction helpful.
  • Michael from Portland, OR
  • Really Easy
  • Less than 15 mins
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this helpful?
Thank you for voting!
My drip pans were in bad shape
2 of 5 people found this instruction helpful.
  • Sandra from Oldsmar, FL
  • Really Easy
  • Less than 15 mins
I removed the old and repaced with new. I never ordered anything one day and got it the next. I'm impressed
Was this helpful?
Thank you for voting!
Just needed new drip pans for burners
1 of 2 people found this instruction helpful.
  • Ann from Cadiz, KY
  • Really Easy
  • Less than 15 mins
Was glad to get the correct ones for a 30 year old stove. Had already wasted $12 shipping trying to order from someone else.
Was this helpful?
Thank you for voting!
2 of the burners were not working arching and smoking
1 of 3 people found this instruction helpful.
  • Tina from Laurel, MT
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts t ogether with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.
Was this helpful?
Thank you for voting!
cooking element shorted out and did not heat.
0 of 1 people found this instruction helpful.
  • Carolyn from Fyffe, AL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Was this helpful?
Thank you for voting!
Wire broken off plug in block
0 of 1 people found this instruction helpful.
  • Robert from Phillipsburg, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Removed old block , cut off wires , used new wire nuts, heat shrink , supplied with parts , job done lowered range top went fishing ...
Was this helpful?
Thank you for voting!
Bowl -Drip and gasket
0 of 1 people found this instruction helpful.
  • Walid from Worcester, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
it was relay easy when you get the right pats .so
Thanks for .
PART Select.
Best regard .
Walid
Was this helpful?
Thank you for voting!
contacts had gotten burnt out/blackened with age so burner was intermittent.
0 of 1 people found this instruction helpful.
  • john from reading, MA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this helpful?
Thank you for voting!
Wire broken going to one electric plug for burner
0 of 1 people found this instruction helpful.
  • John from Shelby Township, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.
Was this helpful?
Thank you for voting!
All Instructions for the ETD646
31 - 45 of 105