ETD643 Caloric Cooktop - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
no heat from burner
0 of 1 people
found this instruction helpful.
-
George from ST. Charles, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.
Was this helpful?
Thank you for voting!
Burner Would Not Heat
0 of 1 people
found this instruction helpful.
-
David from Toledo, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
Was this helpful?
Thank you for voting!
burner wouldn`t stay hot.
0 of 1 people
found this instruction helpful.
-
Cary from Gilbertsville, PA
- Easy
- 15 - 30 mins
-
Screw drivers
First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws fo
... Read more
r the cooktop.I put in the new burner & it worked just like new.
Read less
Was this helpful?
Thank you for voting!
Worn out terminal block
0 of 1 people
found this instruction helpful.
-
John from Brookings, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube ove
... Read more
r the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
Read less
Was this helpful?
Thank you for voting!
contacts in plug-in block badly burned & oxidized
0 of 1 people
found this instruction helpful.
-
william from port st lucie, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Read less
Was this helpful?
Thank you for voting!
burner connector - bad connection
0 of 1 people
found this instruction helpful.
-
Terry from Grand Forks, ND
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this helpful?
Thank you for voting!
Sparks where the heating element plugs into the stovetop
0 of 1 people
found this instruction helpful.
-
Martin from Sayre, PA
- Easy
- 15 - 30 mins
-
Screw drivers
The directions were very clear. I removed the heating element, detached the plug-in block by unscrewing the screw, then cut the wires about 3 inches from the block. I put the shrink-wrap collars around the wires leading to the new block, then attached the wires to the cut ends of the wires leading to the back of the stove, using the con
... Read more
nectors provided in the kit. I couldn't get the collars to shrink as much as shown in the picture. I attached the new block to the stove top using the screw, plugged in the heating element, and it worked!
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.
So the instructions were good, and the heating element is now working. The only problem was the heat shrink collars that go around the connectors: I couldn't get them to shrink much, but that doesn't seem to matter.
Read less
Was this helpful?
Thank you for voting!
range top burners not heating reliably
0 of 1 people
found this instruction helpful.
-
Roy from Moore, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!
Was this helpful?
Thank you for voting!
Right front surface burner did not work due to broken burner plug in wire harness.
0 of 1 people
found this instruction helpful.
-
Raymond from Rock Hill, SC
- Easy
- 15 - 30 mins
-
Screw drivers
Cut power. Removed four attaching screws and raised stove top. Cut two wires of existing burner plug. Used existing plug to select correct plug configuration from parts in kit. Attached new plug and wires to wiring harness using connectors and heat-shrink tubing supplied with kit. Used hair dryer to shrink tubing on connectors. Closed up
... Read more
stove. Restored power. Burner now functional.
Read less
Was this helpful?
Thank you for voting!
holder burnt
0 of 1 people
found this instruction helpful.
-
Paul from lewiston, ME
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people
found this instruction helpful.
-
dicky from mcrae, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su
... Read more
re and disconnect power before starting!!
Read less
Was this helpful?
Thank you for voting!
large burners not working
0 of 2 people
found this instruction helpful.
-
Greg from Versailles, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so yo
... Read more
u have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Read less
Was this helpful?
Thank you for voting!
replace the cook stove's drip bowls instead of cleaning them
-
Dallas from Arlington, TX
- Really Easy
- Less than 15 mins
I removed the burners and then the older drip bowls of the cook stove--and then I put on the new drip bowls and put back on the burners. My mechanical skills were sufficient for the replacement of the drip bowls.
Other Parts Used:
Was this helpful?
Thank you for voting!
The surface burner socket that the burner plugs into melted.
-
Gary from Chesapeake, VA
- Easy
- Less than 15 mins
-
Screw drivers
Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold t
... Read more
he socket, etc.
Read less
Was this helpful?
Thank you for voting!
I needed to replace to two 8* drip bowls on the kitchen range
-
Dallas from Arlington, TX
- Really Easy
- Less than 15 mins
(a) I took out (and threw away) two stained 8* chrome drip bowls on my kitchen range; (b) ti put in two new 8" chrome drip bowls on my kitchen range. I'm pleased that I was equal to the task.
Was this helpful?
Thank you for voting!