EST308 Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
lower heat element would not get to temperature
0 of 1 people
found this instruction helpful.
-
Titus from Madison, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Slide stove out and unplug. Using nut driver (phillips screw driver would work fine) remove screws securing back panel. Remove back panel. Pull off wires from heating element. I made a lose knot on left wire so I could install as removed without confusion - sometimes it matters. Removed 2 screws securing element inside the oven. I ins
... Read more
talled everything as it was - oven works great. I saved over $100 and my wife thinks I'm a genius. Hardest part was cleaning accumulated mess behind the stove.
Read less
Was this helpful?
Thank you for voting!
holder burnt
0 of 1 people
found this instruction helpful.
-
Paul from lewiston, ME
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the one screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Was this helpful?
Thank you for voting!
burner connector - bad connection
0 of 1 people
found this instruction helpful.
-
Terry from Grand Forks, ND
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this helpful?
Thank you for voting!
burner wouldn`t stay hot.
0 of 1 people
found this instruction helpful.
-
Cary from Gilbertsville, PA
- Easy
- 15 - 30 mins
-
Screw drivers
First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws fo
... Read more
r the cooktop.I put in the new burner & it worked just like new.
Read less
Was this helpful?
Thank you for voting!
Worn out terminal block
0 of 1 people
found this instruction helpful.
-
John from Brookings, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube ove
... Read more
r the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
Read less
Was this helpful?
Thank you for voting!
contacts in plug-in block badly burned & oxidized
0 of 1 people
found this instruction helpful.
-
william from port st lucie, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Read less
Was this helpful?
Thank you for voting!
Was baking brownies and all the sudden the heating element started sparking, flaming, and looking like a welding rod.
0 of 1 people
found this instruction helpful.
-
WAYNE from FERGUSON, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I reconnected the wires to the new element and screwed it in to the oven back. Simple and inexpensive fix.
Then I reconnected the wires to the new element and screwed it in to the oven back. Simple and inexpensive fix.
Was this helpful?
Thank you for voting!
Broken oven door hinges
0 of 1 people
found this instruction helpful.
-
James from Brookline, MA
- A Bit Difficult
- More than 2 hours
-
Screw drivers
Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old ... Read more hinges and installing the new ones.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old ... Read more hinges and installing the new ones.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
cooking element shorted out and did not heat.
0 of 1 people
found this instruction helpful.
-
Carolyn from Fyffe, AL
- Really Easy
- 30 - 60 mins
-
Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts-
... Read more
they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Read less
Was this helpful?
Thank you for voting!
Broken Element
0 of 1 people
found this instruction helpful.
-
JOHN from KANSAS CITY, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
Quick as I could with bad knee and empty stomach. Pizza was waiting to be cooked. . The young lady that took my order needs a bonus, exceptional extra effort on her part to get me the part. Very pleased with her attitude and service, hope you can track her down.
Was this helpful?
Thank you for voting!
Burner Would Not Heat
0 of 1 people
found this instruction helpful.
-
David from Toledo, OH
- Really Easy
- Less than 15 mins
-
Screw drivers
One screw taken out, 2 wires switched, new part & screw put in. Burner like new!
Was this helpful?
Thank you for voting!
Wire broken going to one electric plug for burner
0 of 1 people
found this instruction helpful.
-
John from Shelby Township, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Replace the connector and bracket, spliced the wires, put heat to the schrink wrap and I was done.
Was this helpful?
Thank you for voting!
no heat from burner
0 of 1 people
found this instruction helpful.
-
George from ST. Charles, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
I raised the stove top, read the instructions to my son while he did the work, then I lowered the stove top, installed the burner, and it worked like magic.
Was this helpful?
Thank you for voting!
contacts had gotten burnt out/blackened with age so burner was intermittent.
0 of 1 people
found this instruction helpful.
-
john from reading, MA
- Really Easy
- Less than 15 mins
-
Screw drivers
lifted the cover, unscrewed the ceramic wire fastners, put the new part in, and voila, job done and working perfectly
Was this helpful?
Thank you for voting!
burners were shorting out, and not heating very well
5 of 16 people
found this instruction helpful.
-
Matthew from Ogden, KS
- Easy
- Less than 15 mins
-
Pliers
Pretty simple. Turned off breaker. Lifted the top, cut the 2 wires. Going to the burner, put the 2 wire nuts on, and screwed the bracket in.
Other Parts Used:
Was this helpful?
Thank you for voting!