EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

ESS344-OF (ESS3440OF) Caloric Range - Instructions

All Instructions for the ESS344-OF
121 - 135 of 156

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broiler heating element quit working
  • Rhonda from Great Bend, KS
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I had no trouble replacing the Broiler heating element, total time 30 minutes. Just had to pull the range out to unplug it and remove the back sheild of the range, then remove the two push on electrical connections. Then removed one screw holding the element to the inside of the oven, replaced with the new element, attached the connecti ons, but the back sheild back on and it was done.
Was this helpful?
Thank you for voting!
I had to replace the broiler element because it had burned up like a sparkler.
  • Georgia L from Coupeville, WA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I read instructions and hints online. Then, I pulled the range out from between the cabinets and unplugged it (carefully). I used a small Philips head screwdriver to remove the 10 metal screws holding the large metal sheet on the back of the oven. Then I removed the 4 screws holding on the metal sheet on the upper level of the back of the range since it had to be removed to move back the big sheet metal away from the back. The large metal sheet has the power cord threaded through it on the bottom and I left that in place. I then removed the oven door by lifting it up off the hinges after I removed the screw on each side that held the door on the hinges. The door is quite heavy for a girl. I unscrewed the plate at the back of the broiler element, unhooked it from the hangers, and carefully pulled the connectors apart from the oven wiring and the dead broiler element. (Being completely unfamiliar with this kind of connector it took me some time to figure out they slid apart.) Following advice online I had used electrical tape to tape down the wires so they wouldn't slip backwards out of the oven. The new broiler element connectors slid smoothly and easily into the oven wires. I removed the electrical tape I had used as temporary holders, hung the element on the previous wire slings and removed the new wire slings for a backup. I screwed back the plate on the new element into the back of the oven wall. I used the part number orientation on the element to make certain I had it right side up. If I have to do this again it will be easy and take very little time. My biggest problem was getting the oven door back on because it was heavy for me and I was too short to be able to see what I was doing as I repeatedly tried to get the oven door and hinges aligned. Eventually the door was back on and screwed down. Everything that had been unscrewed was put back in place and screwed down tightly. The oven and broiler are working perfectly.
Was this helpful?
Thank you for voting!
Door wouldnt shut evenly.
  • David from Westlake, OH
  • Difficult
  • 1- 2 hours
  • Screw drivers
Ordered hinge, went to Sears bought some tools to finish manufacturing the hinge, tapped out the screw hole, installed the hinge.
Was this helpful?
Thank you for voting!
stove burner no longer would heat up burner element
  • Bonnie from Price, UT
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.
Was this helpful?
Thank you for voting!
oven coil burned out
  • Kathleen from Weston, WI
  • Really Easy
  • 15 - 30 mins
  • Pliers
by myself
Was this helpful?
Thank you for voting!
two of the burners were working intermittently
  • Kevin from Desoto, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this helpful?
Thank you for voting!
Top element not heating
  • Mary from Montgomery, AL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpf ul ML
Was this helpful?
Thank you for voting!
Broken Hinges On Oven Door.
  • DAVID from FRANCISCO, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers
I had already removed the old hinges by removing the screws/bolts and removing the broken hinges from the back side through the drawer below the oven that I had already removed. Took the new hinges and screwed the two metal screws into the top hole on the new hinges after placing hinge in vise, one screw on each then removed them and pla ced them to the side. Determined the right tap from my tap set, and then tapped the bottom two holes on the new hinges, one on each. Placed the bolts that came with the new hinges into the holes I had just tapped, screw them in, then I removed them and placed to the side. Took hinges and bolts / screws to the oven, inserted hinges in through the drawer that I had removed up to each side where hinges would come back out to the front of the oven. Placed screws / bolts one at a time through oven door frame into the hinge on the back side, and then threaded them into the hinges and tightened. Replaced oven door onto new hinges and checked for correct operation. Door works like new.
Was this helpful?
Thank you for voting!
oven light replacement
  • martin from portland, OR
  • A Bit Difficult
  • 15 - 30 mins
  • Pliers, Screw drivers
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!
Was this helpful?
Thank you for voting!
Surface burner block corroded
  • Teresa from Kasson, MN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.
Was this helpful?
Thank you for voting!
Blocks were broken
  • James J from Sweet Grass, MT
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase.. .parts arrived very timely...J. Iriwn
Was this helpful?
Thank you for voting!
Bottom baking element was not heating oven to proper temperature
  • Deanna from Blue Mounds, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unscrewed 2 screws holding the bracket on the back of the stove and disconnected the wires from the two clips. Removed back element, connected new elements & replaced screws to back inside wall of oven. Works like brand new!!
Was this helpful?
Thank you for voting!
Surface Burner not working
  • Cody from Abilene, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new b racket and installed the burner. double checked everything and lowered the top. Done
Was this helpful?
Thank you for voting!
Oven heating element burnt out
  • Mark from Madison, WI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The repair was simple, two screws and plug in and it was done.
Was this helpful?
Thank you for voting!
burner not working
  • Marcia from Wellesley, MA
  • Really Easy
  • Less than 15 mins
burner replaced
Was this helpful?
Thank you for voting!
All Instructions for the ESS344-OF
121 - 135 of 156