EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

ESP379 Caloric Range - Instructions

All Instructions for the ESP379
1 - 15 of 20

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Rivet broke on the right side oven door hinge
7 of 8 people found this instruction helpful.
  • Roger from Pleasanton, CA
  • Easy
  • Less than 15 mins
  • Screw drivers
Regarding my right side oven door hinge replacement, P/N PS2172201

After reading that other people had trouble threading the screws into the new hinge, I looked at the drilled mounting holes in the new hinge. Neither hole was threaded. The smaller hole used a self tapping sheet metal screw which works fine. The larger hole gets a machine screw and will not self tap. Since the instructions say put the screw in "once" to tap the holes before installing the hinge, I tried this. It doesn't work, regardless of what the instructions say. The larger hole should come from the manufacture threaded. I do have a tap and die set so I tapped the hole myself. After that, the installation is a 5 min. ordeal.

Take the two screws, one on each side, out that hold the oven door on the hinges. The door will then pull straight off the hinges. Take the storage drawer below the oven out. Unscrew the top and bottom hinge screws and pull the old hinge out from inside at the bottom. Put the new "threaded" hinge into position and hold from the bottom, inside. Screw in the two screws, large one on the top end, and put the door back on. You can open both hinges about 30 degrees to allow the door to slide back on the hinges easily. Put the last two screws in that hold the door to the hinges and you are done.

Really very easy and saved several hundred dollars in repair bills. I might add that my hinge arrived on time 3 or 4 days after the order was placed.
Was this helpful?
Thank you for voting!
One hinge was broken and the other was Sprung
5 of 6 people found this instruction helpful.
  • William from Social Circle, GA
  • Easy
  • 30 - 60 mins
  • Screw drivers
Removed the door and old hinges and reinstalled the new hinges and added some screws to better support the door ( it was bending a little at the middle and the door would not shut all the way. Now it works fine.
Was this helpful?
Thank you for voting!
Old hinge snapped a rivet. It could no longer hold the weight of the door.
4 of 4 people found this instruction helpful.
  • Frank from Farmingdale, NY
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
I removed the two screws and pryed out the old hinge. I then put in the new hinge. The new one fit well. I went to screw it in with the supplied screws. The screws not only did not fit the hole tapped in the hinge (too big, different tread) but both screws were different from each other. They were different sizes and different types all t ogether. I tried re-using the screws from the originol hinge but they also did not fit. I then got my own self tapping machine screws and finished the job. This job should not have been that hard. If they had supplied the correct screws, It would have taken all of five minutes.
Was this helpful?
Thank you for voting!
Loose terminal caused block to overheat and break
6 of 10 people found this instruction helpful.
  • Dana from Black Mountain, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this helpful?
Thank you for voting!
oven door would fall off when you opened it
5 of 7 people found this instruction helpful.
  • Arthur from Ridgewood, NJ
  • Easy
  • Less than 15 mins
  • Screw drivers
left side hinge was broken. I removed 2 screws to release the old hinge and replaced it with the new hinge.
Part select.com made it easy to pick out the part from the diagram supplied on the web site. After it was ordered it arrived 2 days later.
Was this helpful?
Thank you for voting!
Right hinge broken: left hinge bent
4 of 6 people found this instruction helpful.
  • Stephen from New York, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Instructions with parts are minimal. Looked at exploded drawing and read other installation descriptions on site. From the read I knew it was easier than it looked. Opened oven door. Unscrewed screws about 1/3 of the way up on both sides on inside face of door; these are the only thing attaching the hinges to the door. (Save all the screws you remove - they make work better than the ones with the parts.) The door can now be pulled off the range. I pulled the broken part out of the right side with pliers. Remove the screws below and about 8" up from the hinge on each side. When this is done you can pull the hinge out from the slot from the front. Open the new hinges up and they will slip through these same openings and position them as the ones you removed were positioned. Replace the screws. On the parts I received the lower screw holes on the hinge were not tapped. The original screws worked a bit like self-tapping ones. If you lose any parts or need to get to the hinge from the back you can take out the drawer.
Was this helpful?
Thank you for voting!
I snapped a bolt on the main power terminal block when connecting the pigtail.
3 of 8 people found this instruction helpful.
  • Frank from Palm Coast, FL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Was this helpful?
Thank you for voting!
Broken hinge on oven door
4 of 11 people found this instruction helpful.
  • Robert from Morgan Hill, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
I ordered the part and it was at my door in 2 days. I ordered the part on Wednesday thinking I would install it on the weekend after next. The part showed up on Friday. That was amazing considering I didn't sellect expeidited delivery. I didn't have a manual and have never tried this before so grade my attempt on a curve please. I started by unscrewing the screws closest to the hinge but quickly migrated to the entire face of the range. Pulled the range out and started unscrewing the screws on the side, and then the back. Figuring nothing was coming off and I still couldn't get to the hinge I stopped and regrouped. That's when my wife asked if she could help. I guess I looked distressed. By this time I had removed the drawer and had the range on it's back in the middle of the kitchen with little bowls of screws everywhere. My wife picked up the new hinge and looked it over. Then she started playing with the old hinge which was loose, but I couldn't get it out. She realized that you can remove the old hinge and install the new hinge without taking the whole thing apart. Where was she 30 minutes ago? The hinges came out and the new ones went it in about 10 minutes. It took me another 20 minutes to put back all of the screws I had taken off unnecessarily. Sometimes use your brains instead of a screwdriver. I have the best wife ever!
Was this helpful?
Thank you for voting!
wire came loose and shorted out
1 of 2 people found this instruction helpful.
  • Elizabeth from HOUSTON, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this helpful?
Thank you for voting!
broken hinge
1 of 3 people found this instruction helpful.
  • Jed from Spanish Fork, UT
  • Easy
  • 15 - 30 mins
  • Screw drivers
The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.
Was this helpful?
Thank you for voting!
hinge on oven door broke off
2 of 6 people found this instruction helpful.
  • Janine from Wilkes Barre, PA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predri lled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!
Was this helpful?
Thank you for voting!
Block broke
1 of 4 people found this instruction helpful.
  • Edward from Crimora, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this helpful?
Thank you for voting!
Broken oven door hinges
0 of 1 people found this instruction helpful.
  • James from Brookline, MA
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers
Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.
Was this helpful?
Thank you for voting!
hinge broken again
0 of 3 people found this instruction helpful.
  • Russ from Milford, NE
  • Really Easy
  • Less than 15 mins
  • Screw drivers
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this helpful?
Thank you for voting!
circuit breaker blew
  • Richard from Sarasota, FL
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in abo ut 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.
Was this helpful?
Thank you for voting!
All Instructions for the ESP379
1 - 15 of 20