ERP383 Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drip Pans were stained and burned on.
1 person
found this instruction helpful.
-
Sandra Collignon from SANTA CLAUS, IN
- Really Easy
- 30 - 60 mins
Replaced drip pan. Notch did not want to match the burner notch. Was a close fit bit with a little pressure made it work.
Was this helpful?
Thank you for voting!
Range oven door switch need replaced
1 person
found this instruction helpful.
-
Ruth from Gastonia, NC
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
I raised the top of my Whirlpool Continuous Cleaning Canning Oven, then had to unscrew 3 screws and a lock nut, then raise top about 4 inches, so I could put my hand inside to unplug the wires to the switch, and push it through the hole in front, of oven. Then put the new switch through hole and plug in new switch. Then screw down top;
... Read more
and close lid. Part #866294
Read less
Was this helpful?
Thank you for voting!
Racks would fall off of the tracks when the broiler was used
1 of 2 people
found this instruction helpful.
-
Andrew from Neptune, NJ
- Very Difficult
- More than 2 hours
I ordered new racks to see if they weere out of alignment. The new racks fell from its tracks after the broiler was heated. It seems the oven cabinet is expanding with the heat and the rack width does not compensate for that. The new racks did not solve the problem so I do not know what can be done next. Any shelf support would have to be
... Read more
heat resistent. Replacing the oven cabinet is not a good option and no gauantee it wouldn't continue with this stove.
Read less
Was this helpful?
Thank you for voting!
Drip pans were old and with burnt on food that I couldn't get off. Disgusting!!
1 of 2 people
found this instruction helpful.
-
Nicki from ELSIE, NE
- Very Easy
- Less than 15 mins
No problem Took off old ones and replaced with new.
Was this helpful?
Thank you for voting!
The three braces under the coils had weakened and fallen apart
2 of 5 people
found this instruction helpful.
-
Suzanne from COZAD, NE
- Very Easy
- Less than 15 mins
I simply pulled out the old coils and plugged in the new ones. I saved the little pieces that accompanied each coil, because I didn't know what they were used for.
Was this helpful?
Thank you for voting!
Missing An Oven Rack Due To Plastic Fire In Our Oven. Plastic Melted Onto The Rack...Instead Of Taking The Time To Melt The Rest Off, My Husband Threw It Away =(
1 of 2 people
found this instruction helpful.
-
Nicole from Rogers, MN
- Really Easy
- Less than 15 mins
Bought a new one. . Three years later =)
Was this helpful?
Thank you for voting!
drip-bowls wore out
1 of 2 people
found this instruction helpful.
-
Ronald E from Rochester, NY
- Really Easy
- Less than 15 mins
i read the installation instructions and followed them. first i made sure that each heating element was off. next i carefully removed each one (a total of 4) from it's plug and lifted the worn out drip-bowl up and replaced it with the new one. finally i pluged in (a total of 4) heating elements and turned them on to make sure them were wo
... Read more
rking and they did.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Simple - needed to replace the drip pans on the stove between tenants in a rental apartment
1 of 2 people
found this instruction helpful.
-
Tama from Pacific Grove, CA
- Really Easy
- Less than 15 mins
This wasn't much of a repair -- rather a replacement of a simple abused part. At the same time, PartSelect allowed me to order what I needed after two failed attempts to buy replacements that would fit the range. I'll remember PartSelect if we need parts for other older appliances in the rental units.
Was this helpful?
Thank you for voting!
Old burner pan warped.burner sat at 15 degree angle.
1 of 2 people
found this instruction helpful.
-
Michael from Portland, OR
- Really Easy
- Less than 15 mins
Removed burner and then burner pan.Then replaced pan and reinstalled burner.
Was this helpful?
Thank you for voting!
Wire Racks very old and very dirty
1 of 2 people
found this instruction helpful.
-
Paul from Belmont, MA
- Really Easy
- Less than 15 mins
I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased
Was this helpful?
Thank you for voting!
Replace oven racks
2 of 5 people
found this instruction helpful.
-
Gregory from Davenport, IA
- Really Easy
- Less than 15 mins
Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!
Was this helpful?
Thank you for voting!
replace coroded drip pans
1 of 3 people
found this instruction helpful.
-
Marlin F. from Holbrook, AZ
- Really Easy
- Less than 15 mins
replaced the drip pans. Fit perfect. No problems
Other Parts Used:
Was this helpful?
Thank you for voting!
The problem was that the 2 big burners were not working.
0 of 1 people
found this instruction helpful.
-
Bonnie from Highwood, MT
- Easy
- 1- 2 hours
-
Screw drivers
I ordered the 2 burners that were not working. When I got the burners, I discovered that one of the burners was still working and the wiring under that on had burned out. So I ordered the little box kit and repaired it. I only needed to strip wires and twist together and replace the small box. Now all are working and I am cooking with
... Read more
all four burners again. All for about $50.
Read less
Was this helpful?
Thank you for voting!
Ugly looking drip bowl.
0 of 1 people
found this instruction helpful.
-
Irina from Green Cove Springs, FL
- Really Easy
- Less than 15 mins
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.
Was this helpful?
Thank you for voting!
needed to replace one burner
1 of 4 people
found this instruction helpful.
-
Donna from Carver, MA
- Really Easy
- Less than 15 mins
the part arrived in two days. Just had to remove the old one and pop in the new one and it was that easy. I was amazed at how soon the part was delivered and happy to have a working burner again.
Was this helpful?
Thank you for voting!