My Orders
- Home
- ERFC2393AS0
- Instructions
ERFC2393AS0 Electrolux Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Thin, flexible edge on outermost door gasket was tearing from the main gasket, likely due to being rubbed when accessing refrigerator..
2 of 2 people
found this instruction helpful.
-
Dennis from Oley, PA
- Really Easy
- Less than 15 mins
Gasket is held in place by an extrusion on the back side. Simply remove the old gasket and press the new gasket's extrusion into the track on the door.
Was this helpful?
Thank you for voting!
Refrigerator wasn't staying cool enough
2 of 2 people
found this instruction helpful.
-
Karl from Brookfield, CT
- Really Easy
- Less than 15 mins
Easily removed the old gasket and put the new ones on exactly the same way the old ones came off but in reverse
Was this helpful?
Thank you for voting!
Replaced door gaskets with new ones
2 of 2 people
found this instruction helpful.
-
Andres from Golden Valley, MN
- Really Easy
- Less than 15 mins
Removed the old door gaskets by hand and attached the new ones by inserting the edges in the existing grooves
Was this helpful?
Thank you for voting!
One blade broke from condenser fan
12 of 32 people
found this instruction helpful.
-
Chris from Lockport, NY
- Really Easy
- Less than 15 mins
The part i recieved, from parts select was a larger in circumfrence (<1/4) than the original. However i was not aware of this until after i treid to repair it.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon be ... Read more gan to make aloud noise, due to there not being enough clerance.
I removed the broken fan from the condenser. This was very sipmle.
When i pluged the refridgerator back in to the outlet the fan tried to start up but soon be ... Read more gan to make aloud noise, due to there not being enough clerance.
Read less
Was this helpful?
Thank you for voting!
Previous seal had a tear and cold air was leaking around seal
2 of 2 people
found this instruction helpful.
-
Daniel from Hampton, NH
- A Bit Difficult
- 1- 2 hours
Pulled the old seal out of the groove. Placed new seal in the groove. New seal has to be heated and massaged to get it into proper form so it does not leak. I have been continuously heating and massaging to get the seal to get it in the proper form. Been working on it for a week. Almost there.
Was this helpful?
Thank you for voting!
THE GASKET LOCKING INSERT DID NOT FIT THE BOTTOM OF THE DOOR.
2 of 3 people
found this instruction helpful.
-
Robert from Lexington, SC
- A Bit Difficult
- 1- 2 hours
I REMOVED THE OLD GASKET BEING VERY CAREFUL TO SEE EXACTLY HOW IT CAME OFF. I INSERTED THE LOCKING INSERT INTO THE TRACK IN THE DOOR WHICH DID NOT FIT AS THE OLD ONE DID. AFTER USING TREMENDOUS FORCE WITH MULTIPLE TOOLS I DID MANAGE TO GET THE TOP AND THE SIDES TO LOCK INTO PLACE AND EVENTUALLY HOLD. THE BOTTOM OF THE GASKET DID NOT HO
... Read more
LD SO I USED CLEAR CAULK AND TAPE TO HOLD THE GASKET IN UNTIL THE CAULK CURED. AFTER THE CAULK CURED THE GASKET HAS, SO FAR, REMAINED TIGHT.
Read less
Was this helpful?
Thank you for voting!
ICE WOULDN'T DISPENSE FROM ICE BOX
4 of 11 people
found this instruction helpful.
-
James from ORLANDO, FL
- A Bit Difficult
- 30 - 60 mins
I read other suggestions trying isolate auger motor shaft with pliers while turning bar drive. needle nose pliers could hold the shaft. bar drive just would spin. so took the whole ice box assembly out
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from t ... Read more hat point. Left handed threads by the way.
(only 2 screws) and with a metal cutting blade used the sawzall to cut along the shaft. freed it up enough to then unscrew it from t ... Read more hat point. Left handed threads by the way.
Read less
Was this helpful?
Thank you for voting!
The new motor mount screw holes were not threaded.
1 of 5 people
found this instruction helpful.
-
Greg from henrico, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Socket set
I had to tap the screw holes with a 8/32 tap so that the screws would not bind.
Was this helpful?
Thank you for voting!
From day one the installer did not tighten the screw in the freezer handle. It finally came apart. They didn't leave me the Allen wrench for my fridge.
1 of 5 people
found this instruction helpful.
-
Margaret from WINDER, GA
- Very Easy
- Less than 15 mins
Simple tightening of the screw with the right tool.
Was this helpful?
Thank you for voting!
No problems
2 of 9 people
found this instruction helpful.
-
Nancy from LEHIGH ACRES, FL
- Really Easy
- 15 - 30 mins
-
Wrench (Adjustable)
I had no problems. Screws arrived sooner than expected. It was a very simple installation. Very pleased with both the product and service.
Was this helpful?
Thank you for voting!