EMO3000CSS03 General Electric Microwave - Instructions

Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE

Simply ordered a replacement part that was quickly and coveniently mailed to my home.

Handed the part to my son. He unscrewed 5 screws in the base of the microwave, it dropped down. The light mechanism was clearly in view. With the exception of some corrosion on the old piece, it was simple to remove and replace, put back together, screw back up and all worked fine.

Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Put it in place. Ordered replacement over internet on Wednesday and part arrived Friday. Very fast service!

It took less then 10 minutes to order. Received new part with 3 days

Removed bottom cover of microwave, involved removing 7 screws, removed turntable motor, involved disconnecting wire harness plug, and 2 screws, connnected wiring to new motor and reinstalled with original hardware

My microwave was squealing horribly and replacing the turntable motor (SUPER easy btw) didn't fix it. So I figured it was a spun bearing or bushing in the cooling fan (spoiler alert -- it was!). Installation was simple and did NOT require removing the cabinet-mounted microwave from its position above our stove: Unplug microwave, carefully unscrew the 2 screws holding the vent grate above the door, remove the grate, then unscrew the one screw holding the top of the control panel to the case. Carefully pivot top of control panel down and unhook it from the case (at the bottom of the control panel there are two little legs or extensions that insert into slots in the case). Then disconnect the 3 or 4 wires that attach the control panel to the wiring harness (I marked them each with tape so I would remember where they go, but you can just take a picture with your phone). Set the control panel aside. Where the control panel was, you will be looking at the fan, with a bunch of wires between you and it. Take another phone picture for reference, just in case. Disconnect the various wires, starting at the top right and working your way around clockwise. I marked each wire with a piece of tape and a number, starting from 1 and working my way around an imaginary clock face. I think I got to 12 and then the last two (sort of buried in the middle) I labeled as "0" and "-1" but you can use any numbering series you like. Once the wires are all disconnected you can gently push them aside and unscrew the two screws holding the fan assembly in place, and disconnect the fan wire. Then gently maneuver the fan assembly out the front of the case. Installation is simply the reverse of this simple disassembly process. Voila! Back to a nice quiet microwave.

1. Pried off the choke on rear of door to expose screws to door handle. 2. Using Phillips-head screw drive, removed the two scews to door handle. 3. Removed cracked frame from door - a bit difficult because frame is held in place by plastic tabs. 4. Removed door latch assembly from cracked frame and installed on new frame. 5. Refitted door handle to new frame. 6. Snapped new frame in place - again, somewhat difficult because of plastic tabs. 7. Replaced choke to rear of door - be careful because exact positioning of the choke is required and misalignment might crack the choke. 8. Enjoy saving over $100 in labor.

I used the internet and your directions to complete the repair. It was easy!

removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.

First I replaced the cracked cooking tray and I was done.

I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.

Removed screws and old parts. Fitted new part to door and put screws back in.

Replacement tray was installed. It was larger than the original tray, but it fits in.