EJC314 Caloric Range - Instructions

Cut the old wires off, removed the screw holding the clamp, installed the new parts. Problems I encountered were the wire nuts. They were too small for the wire gage of the replacement part and the original oven. I had larger wire nuts in my workshop. Also, why so many extra parts like the shrink wrap tubing, two metal clamps to hold the socket, etc.

Turned off stove breaker. Unscrewed burner from stove top, took out burner and spill pan. Lifted top of stove, cut the wire as instructed and put all parts together as instructed. Placed everything back together as instructed. I did it myself!

Unscrewed screw holding bracket. Used side cutters to cut wires. Replaced the bracket, put the shrink wrap on wires, twisted wires together and held with wire caps. Shrunk the wrap with lighter. I'm a 67 year old female.. No problems.

slide new burner in slot and turned on stove. Worked perfectly.

It was a very easy fix. I followed the instructions that came with the kit and cut the original cable. Everything you need is in the kit; very few parts. Piece of cake and saved a lot of money an appliance repair person would have charged. This burner works better than the rest. I'm seriously considering replacing the other three blocks.

The four kits arrived, use of a pliers and shink wrap and side cutters...strip wires, twist wires connect wire ties, shrink wrap...little fire, plug the elements...done...four in about ten minutes...Instructions in each package...no problem...very easy...saved twice the money or more...Thanks for the parts...recommend this site purchase...parts arrived very timely...J. Iriwn

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

I lifted the stove top and cut the two wire connected to the block. Attached the new wire connectors, new block and checked to make sure it was working. The part that took the longest was getting the screw out of the mounting brracked(it was corroded on). I sprayed some WD40 and waited 5 minuts, it came loose. Then i mounted the new bracket and installed the burner. double checked everything and lowered the top. Done

Bought two new replacement burners,they work great!

burner was shorting out replaced part works great

loosened the screw holding the block pulled it out toget to wire cut it about 4 inches long followed the inst.with block kit and it was a breeze. burner working fine now should have did it sooner.

I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred the bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.

I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were 2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!

After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good directions.

Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpful ML