EJC312 Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I snapped a bolt on the main power terminal block when connecting the pigtail.
3 of 8 people
found this instruction helpful.
-
Frank from Palm Coast, FL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver.
... Read more
Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.
Read less
Was this helpful?
Thank you for voting!
The Problem Was That The Plug Was Gone It Fell Down Out Of The Bracket
1 of 2 people
found this instruction helpful.
-
Elnora from Brundidge, AL
- Easy
- 15 - 30 mins
-
Screw drivers
I took the old wires and plug off and replaced it with the new block it works fine
Was this helpful?
Thank you for voting!
Sockets burnt out.
1 of 2 people
found this instruction helpful.
-
James from Bear, DE
- Really Easy
- 15 - 30 mins
-
Screw drivers
Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.
Will buy from Part Select Appliance again.
Was this helpful?
Thank you for voting!
wire came loose and shorted out
1 of 2 people
found this instruction helpful.
-
Elizabeth from HOUSTON, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this helpful?
Thank you for voting!
Three of four electric coils won't turn on
1 of 2 people
found this instruction helpful.
-
Arsenio from Beaverton, OR
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as supp
... Read more
ort to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.
Read less
Was this helpful?
Thank you for voting!
Stove Burner wouldn't heat up
1 of 2 people
found this instruction helpful.
-
Donna from Sandwich, MA
- Really Easy
- Less than 15 mins
Someone did the repair for me.
Was this helpful?
Thank you for voting!
broiler pan missing
1 of 2 people
found this instruction helpful.
-
RAYMOND from JACKSONVILLE, FL
- Really Easy
- Less than 15 mins
ordered new broiler pan
Was this helpful?
Thank you for voting!
Large burner on stove not working
1 of 2 people
found this instruction helpful.
-
Cherie from Dowagiac, MI
- Really Easy
- Less than 15 mins
I removed the heating element and noticed that the prongs were corroded. I looked for a model number but couldn't find it so it made it difficult to find a replacement until I got on this website. I found the replacement part and also found that as I checked for other sites for this part this company was the most resonable priced.
T ... Read more he part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.
T ... Read more he part arrived and I replaced it in seconds. Turned it on and it worked immediately. Super easy.
Read less
Was this helpful?
Thank you for voting!
Burner ceramic disintegrated & spalled
1 of 2 people
found this instruction helpful.
-
Gary L from North Tonawanda, NY
- Really Easy
- Less than 15 mins
Pulled buner element out of socket as you would for detailed cleaning. Replaced burner element & drip pan with OEM parts. Fit was perfect, tested burner on all heat ranges, good as new.
Was this helpful?
Thank you for voting!
2 of the burners were not working arching and smoking
1 of 3 people
found this instruction helpful.
-
Tina from Laurel, MT
- Really Easy
- 15 - 30 mins
-
Screw drivers
Time was do to the fact that I replaced two elements! I turned off the power to the braker box, unplugged the stove and removed the screw holding the element plug in, removed the part, and cut the wires where they were clean looking (not damaged by smoke or the arch) I then stripped the wire and took the new part and twisted the parts t
... Read more
ogether with the caps and then put the heat shrink on and used the blow dryer on them, attached the part to the bracket and screwed it to the hood of the stove plugged the burner in, plugged in the oven and turned on the power tested it worked, did the same for the next burner and yes mind you I am a woman it was very easy to do.
Read less
Was this helpful?
Thank you for voting!
cooking element shorted out and did not heat.
0 of 1 people
found this instruction helpful.
-
Carolyn from Fyffe, AL
- Really Easy
- 30 - 60 mins
-
Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts-
... Read more
they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Read less
Was this helpful?
Thank you for voting!
burner wouldn`t stay hot.
0 of 1 people
found this instruction helpful.
-
Cary from Gilbertsville, PA
- Easy
- 15 - 30 mins
-
Screw drivers
First I lifted the cooktop out of the countertop & removed the screws so I could access under the burners.Then I cut the wires for the old plug-in block & then stripped the wires.Next I connected the new wires with the wire nuts & then used a lighter to shrink wrap the wire nuts.Then I screwed in the new block & re-installed the screws fo
... Read more
r the cooktop.I put in the new burner & it worked just like new.
Read less
Was this helpful?
Thank you for voting!
Worn out terminal block
0 of 1 people
found this instruction helpful.
-
John from Brookings, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
Turned off the power to the stove. Removed the 'burners' and 'burner' trays. Removed the screw that secured the bad block. Lifted the top of the stove. Cut the two wires to the bad block., stripped the wires about 1/2", slipped the shrink tube over the wires. Connected the new block with two porcelan wire nuts. slipped the shrink tube ove
... Read more
r the wirenuts and heated it with a lighter. Closed the top and secured the terminal block clip with a screw. Turned the power back on: voila!
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
All the necessary parts came in the repair kit, delivery was timely. Very easy project.
Read less
Was this helpful?
Thank you for voting!
contacts in plug-in block badly burned & oxidized
0 of 1 people
found this instruction helpful.
-
william from port st lucie, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
First I removed the one screw that held the element in place. I then pulled the element out about 3 inches and cut the two wires...)
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Assembled the block parts.
Installed shrink sleve and applied wire nuts to electrical connection to 2 wires then shrunk the sleve.
Did the above procedure for 2 heating elements.
They w ... Read more ork very well now.
Read less
Was this helpful?
Thank you for voting!
burner connector - bad connection
0 of 1 people
found this instruction helpful.
-
Terry from Grand Forks, ND
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this helpful?
Thank you for voting!