EIMED60LT4 Electrolux Dryer - Parts

This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only comes back when it drops by at least 70 degrees Fahrenheit. If your dryer is overheating, taking too long to dry clothes, or is not producing...Read more enough heat, replacing the thermostat could be the solution to your problem. The tools needed for this part are a Phillips screwdriver, putty knife, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions and guidance.

This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be...Read more one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.

This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.

This dryer belt is one of the most important parts in a dryer and is what allows the dryer drum to spin/rotate. If the dryer belt is damaged or broken, the drum will not spin or will have difficulty in doing so, and your clothes will still be damp after a cycle as a result. This belt is made of durable material and can wear down over time...Read more and extended use of the dryer. Replacing a dryer belt will require some disassembly of your dryer, so a screwdriver and wrench will be needed to access and replace it. This belt is an individual OEM part.

Sold individually.

This replacement drum support roller helps keep your dryer drum turning smoothly and quietly during operation. Designed for reliable performance, it supports the drum as it rotates to help reduce excess noise, vibration, and wear. Replacing a worn roller can help restore proper drum movement and improve dryer performance. For installation...Read more, unplug the dryer, access the drum support area, and replace the old roller with the new component. Always wear work gloves for added safety during repairs.

This dryer thermal fuse is a critical safety component designed to protect the appliance from overheating. It automatically shuts off power to the motor or heating system if excessive temperatures are detected, helping prevent damage or potential fire hazards. Once the fuse is triggered, it cannot be reset and must be replaced. A faulty t...Read morehermal fuse may cause the dryer not to start, run without heat, shut off prematurely, or operate at unsafe temperatures. Replacing this component helps restore safe and proper dryer operation.

This moisture sensor assembly ensures your dryer delivers optimal performance by detecting the moisture level in each load. By accurately measuring dampness, it allows the appliance to adjust cycle times automatically, preventing over-drying or under-drying and improving energy efficiency. Ideal for resolving issues such as clothes coming...Read more out damp, overly dry, or cycles ending too soon or running too long, this durable component restores precision and reliability. Installation is simple—disconnect power, remove the old sensor, and secure the new one in place.

This part is the replacement screw for your washer. The head is approximately inch in diameter and the screw is approximately 3/4 inch in length. It is made of metal and is sold individually. This is an authentic OEM part sourced directly from the manufacturer.

This drive motor includes the pulley for the dryer drum belt. The motor has reverse threads for the blower wheel. Please disconnect the power before starting your repair. This is a genuine OEM part.

This dryer rear air duct is designed to channel heated air from the burner or heating element into the drum and guide moisture- and lint-laden air toward the exhaust, ensuring optimal airflow and drying performance. Constructed from durable metal to withstand high temperatures, it measures approximately 34.6 inches in length and 3.8 inche...Read mores in height and includes mounting points for internal components such as thermostats. Installation is straightforward—remove the damaged duct and secure the new one in place. Replacing a worn or damaged duct helps prevent overheating, improve drying efficiency, and eliminate issues like lint bypassing filters or marks on clothing.