EIMED60LT3 Electrolux Dryer - Instructions

When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replac ... Read more ing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)

Removed back of dryer with electric nut driver. Lots of screws. Removed old heating element to better access wires and thermostats. Removed baffle at end and transferred to new heater element. Transferred thermostats to new element, reconnected wiring in correct order. Installed new heater element in correct position using tab to loca ... Read more te. Replaced back of dryer. Reconnected dryer vent. Toughest part was squeezing out of space after reconnecting dryer vent. Unfortunately, too short for my weight.

1. Loosened the 3 screws inside of the drum
2. Removed the entire back of the dryer (lots of screws)
3. Removed the old vent (there are 2 screws at the bottom that hold it in)
4. Install new vent (put the screws back in)
5. Close up back and proceed to put all of the screws back

By undoing the single screw which holds the sensor in place, the old one falls off. To replace: simply pop the two wires on their connections (small metal studs on the back), slide clip/wire end of sensor in place and replace the screw. You are back in business! Very simple repair that a DIY can save a ton!

I removed the front, top and back panels of the dryer, installed belt around drum and through the pulley system so the belt was snug, replaced all screws and panels, and done.

Getting to the element and putting the machine back together, in my case, was the most difficult part. There are tons of youtube videos that can guide you through the removal and replacement better than I can. I recomend watching those videos and taking pictures of the old element prior to removing it. Also, I would put all the screws in ... Read more separate ziplock bags with labels on them because every screw for my model was unique. I would also tape and label the electrical wires too.

Tight quarters but went well, fairly easy except for the far back screw that secures the element to back of dryer. Would have been easier if I removed drum but I didn’t want to disassemble that much. All is good and wife is ?? . If need help with disassemble Utube is your friend.

followed the instruction on you tube, the part was exact, there was nothing to guess, basically you take the whole front off of the dryer, that in itself is easy (follow instructions), once you get to the element, just plug and play. the worst part was a set screw in the back that did take some patience, but finally did get it in. I am ... Read more not a mechanic in the least, trust me, if I can do it then anyone can. you will need regular Philips screw driver and one short one, really short, mine is about 2 inches in length, also I used manual one, allot of plastic, so I would not recommend electric drill or electric driver. also a good pair of plyers, but small not large.

followed the repair video and replaced thermal fuse and thermostat(recommend replacing both due to the problem could of resulted in either part being the cause),Repair went relatively easy.I also recommend to clean and vacuum the dryer while you have it all apart due to a lot of lint buildup and don't forget to unplug before servicing!Sta ... Read more y Safe!!!

We followed a YouTube video and did the repair ourselves over an afternoon. We had one screw leftover (?) but everything went back together and now the dryer works like a dream! We bought a PartSelect part because we don't want to have to do this very often! ??

Removed the back panel and the exhaust hose.removed the heater element and changed the thermostat wire was melted cut damaged part of wire soldered and rapped with black electrical tap

Removed screw and disconnect wires. Connect wires to new Moisture Sensor and slide clip to right side of dryer and tighten screw on left side.

Had to loosen drum and move it forward to get at switch. Didn’t have to remove belt.

Remove top lid by pushing tab on either side with a putty knife. Disconnect the 2 wire carriages on right. Remove one
phillips head screw on each side that holds front panel to dryer body. Remove front panel by using flat head screwdriver to pry panel from body. Remove thermostat located on bottom right attached to front of mot ... Read more or on a plastic body by removing two phillips head screws. Disconnect wires and place on new part.

Just remove and replaced no tools required