EIFLS60LT0 Electrolux Washer - Instructions

Bought new part. #1 Lesson learned: Always inspect the actual part number of the ordered/received part. Verify with number marked on the item somewhere. We did not do this and turned out we reinstalled a slightly smaller bellow (wrong part number received in shipment). We were able to fully install it but it was minutely not laying perfec ... Read more tly around the diameter. So minor we did not notice. We did have great difficulty installing though. Anyway, after 1st test run, bellow already had developed a small hole in bottom right quadrant from rubbing on the drum. Left a bunch of gray powdery debris on the drum too. We did not realize error until that point. Took bellow off again to verify part number on it. It was wrong. That explained why the door was so very tight to close and difficult to open. Other than all that, use the video to do the install. It was free to view and easy to follow.

First, I went to the PartSelect website and easily found the part at a reasonable price. I ordered it early on a Wednesday afternoon, and gladly spent the extra $25 to ship it overnight. That evening, PartSelect sent me an email stating that the part had shipped that very day, and - mistakenly - I took that literally. FedEx tracking predi ... Read more cted that the part would arrive on Friday, July 5, which made sense because the 4th was a holiday.
But I found out that the part had actually shipped on the 3rd, as the email had informed me. It didn't actually ship until the 4th - up until then, a "shipping label" had been created but it had not shipped. FedEx then revised their arrival date to Monday, 8 July.
That clearly wasn't satisfactory. So I went to my local parts distributor, Dayton Appliance Parts, a fifteen-minute drive from my house, and got the same part for $3 cheaper, plus without the $25 shipping fee that PartSelect had charged me for overnight-shipping-that-isn't-actually-overnight-shipping.
Once I had the part in hand, installation was a breeze. Two screws removed, pulled the striker, replaced the new part and the screws. Less than two minutes.
But no thanks to PartSelect.

Parts took twice as long to arrive shipped from Utah to Houston, Texas. Once arrived parts were straight forward to install.
1) Open the door by tripping the door strike using yard trimmer line.
2) Turned Power off (unplugged unit)
3) Used needle noses pliers to remove door rubber boot retainer
4) Folded right-side ... Read more of rubber in to removed switch assembly
5) Used Phillips screwdriver to remove switch assembly screws, navigated damaged switch part forward then disconnected line.
6) Connected new switch to line, navigate part back into washer and screwed back in.
7) Repositioned door rubber boot and reattached door boot retainer wire with hands and needle noose pliers.
8) Replaced door strike using Phillips screw driver.
9) Re-plugged washer power to outlet, closed door and ran a test cycle. All good!

Still waiting on the part. It apparently is on back order and I'm still waiting to get the part to try and repair the dryer.

I estimate an hour to replace the part if I ever get the part.

1 you have to order a new motor control board
2 unscrew the back panel
3 unscrew the top panel
4 unscrew the bracket
5disconnect the old motor control board
6 connect the new motor control board

Replaced the door latch. Don't pay for overnight or 2 day delivery it will not get there. Paid for 2 day it arrive a week later. They will not refund the postage.

R and r

All that was needed was a Phillips screw driver. Getting the door latch assembly out was a bit more effort then the door striker. You have to remove the chrome ring around the door opening first. Requires backing out screw on lower left part of the chrome ring to remove

I replaced the thingy and the whatsit, turned the machine off, then on, and the door worked properly thereafter.

amazing 2 screws out part out part in 2 screws in done 2 minutes thank you for such a easy fix

Did it with no problems at all just followed the video step by step worked great done in 1hour!

put new part did reset on main controles