EHT-345 Caloric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
cooking element shorted out and did not heat.
0 of 1 people
found this instruction helpful.
-
Carolyn from Fyffe, AL
- Really Easy
- 30 - 60 mins
-
Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts-
... Read more
they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Read less
Was this helpful?
Thank you for voting!
Broken oven door hinges
0 of 1 people
found this instruction helpful.
-
James from Brookline, MA
- A Bit Difficult
- More than 2 hours
-
Screw drivers
Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old ... Read more hinges and installing the new ones.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old ... Read more hinges and installing the new ones.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
element was busted
0 of 2 people
found this instruction helpful.
-
john from new port richey, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
shut off circut breaker. un pluged stove removed back panel disconected 2 wires on element. removed 1 screw that holds element in place pull out old element put in new reassemble
Was this helpful?
Thank you for voting!
Lower Bake Element burned out
0 of 2 people
found this instruction helpful.
-
Sharon from Sturgis, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on
... Read more
Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!
Read less
Was this helpful?
Thank you for voting!
large burners not working
0 of 2 people
found this instruction helpful.
-
Greg from Versailles, IN
- Really Easy
- Less than 15 mins
-
Screw drivers
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so yo
... Read more
u have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Read less
Was this helpful?
Thank you for voting!
2 of the small burners just fell apart
1 of 5 people
found this instruction helpful.
-
Janice M from Ocala, FL
- Really Easy
- Less than 15 mins
I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people
found this instruction helpful.
-
dicky from mcrae, AR
- Really Easy
- Less than 15 mins
-
Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su
... Read more
re and disconnect power before starting!!
Read less
Was this helpful?
Thank you for voting!
hinge broken again
0 of 3 people
found this instruction helpful.
-
Russ from Milford, NE
- Really Easy
- Less than 15 mins
-
Screw drivers
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this helpful?
Thank you for voting!
Baking element overheated and split into two parts.
0 of 3 people
found this instruction helpful.
-
Derek from Gilford, NH
- Really Easy
- 15 - 30 mins
-
Screw drivers
First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.
Was this helpful?
Thank you for voting!
stove burner no longer would heat up burner element
-
Bonnie from Price, UT
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the burner element, then the drip pan. I took off the old block. Then I had to strip the old wires. Then I put on the heat sleeve, then attached the new wires to the old wires with nuts. Put heat sleeve over this and heated with lighter. Then put everything back together.
Was this helpful?
Thank you for voting!
oven coil burned out
-
Kathleen from Weston, WI
- Really Easy
- 15 - 30 mins
-
Pliers
by myself
Was this helpful?
Thank you for voting!
two of the burners were working intermittently
-
Kevin from Desoto, MO
- Really Easy
- 15 - 30 mins
-
Screw drivers
I shut off the breaker checked for power then cut old plugs making sure to allow a little slack. Tightened down wire nuts put on a couple wraps of electrical tape and that was it. Burners work great now I would reccomend this product to anyone with a similar problem.
Was this helpful?
Thank you for voting!
Plug block was broken
-
Mark from Hillsboro, OR
- Easy
- 15 - 30 mins
-
Screw drivers
I removed the entire burner assembly to avoid having to turn things off at the breaker - the whole assembly can be removed completely from the stove I had. Once it was out and disassembled, the toughest part was putting the new wires into the new block correctly. Once that was done, I had to select the right mounting bracket - there were
... Read more
2 in the kit. Easy, just attention to detail. The rest of the instructions were easy to follow, re-doing the wires. The re-assembly was trivial, and it worked first time!
Read less
Was this helpful?
Thank you for voting!
Burners did not get hot or went on and off
-
Boyd from kalamazoo, MI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
After carefully inspecting existing burner receptacles, I unscrewed them, raised and propped stove top. Determined which bracket to use from new kit and proceeded to cut and strip wires, twist ends together with supplied ceramic caps and heated shrink wrap on that junction. Works great. BTW got parts in 2 days in great shape and good dir
... Read more
ections.
Read less
Was this helpful?
Thank you for voting!
Top element not heating
-
Mary from Montgomery, AL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Ordered wrong part at first caused me to blow out two elements. With the help of PartSelect I was able to get the right surface block terminal and replaced both of them, then found out I had a bad switch, they got the switch within 2 days I had my stove working good again. Thanks to PartSelect. Also watched the video which was very helpf
... Read more
ul ML
Read less
Was this helpful?
Thank you for voting!