EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

EHS345-OF (EHS3450OF) Caloric Range - Instructions

All Instructions for the EHS345-OF
106 - 120 of 156

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner connector - bad connection
0 of 1 people found this instruction helpful.
  • Terry from Grand Forks, ND
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed burner and tray. Removed burner connector from stove top using screw driver.
Removed existing heat shrink and wirenuts.
Installed new connector - wire nuts and heat shrink. Used lighter to shrink.
Took 20 minutes.
Was this helpful?
Thank you for voting!
range top burners not heating reliably
0 of 1 people found this instruction helpful.
  • Roy from Moore, OK
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the original burner element sockets and replaced with parts provided in kit. Instructions were simple and easy to follow, problem completely solved in 20 mins!
Was this helpful?
Thank you for voting!
Broken oven door hinges
0 of 1 people found this instruction helpful.
  • James from Brookline, MA
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers
Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.
Was this helpful?
Thank you for voting!
cooking element shorted out and did not heat.
0 of 1 people found this instruction helpful.
  • Carolyn from Fyffe, AL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I had bought the 1st set of plug-in blocks at lowes, They were the only type they had the univeral ones! They did not hold the elements plug tight enough and half the time they would have to be punshed in more then they would snap and sizzle- I ordere the newer style and they have done great they are better made and heavier metal parts- they elements fit in snuggly and do not sizzle or nor do I have to push the element in. This stove is 35 years old and I have replaced most everything on it. But it's still cooking...
Was this helpful?
Thank you for voting!
element was busted
0 of 2 people found this instruction helpful.
  • john from new port richey, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
shut off circut breaker. un pluged stove removed back panel disconected 2 wires on element. removed 1 screw that holds element in place pull out old element put in new reassemble
Was this helpful?
Thank you for voting!
Lower Bake Element burned out
0 of 2 people found this instruction helpful.
  • Sharon from Sturgis, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Two screws in the oven removed the old part and the wires unplugged from the unit. When the new part came in , it was plug and play. Plugged the wires into the new part, put part into holes in oven and screwed the screws back in place and we were ready to go. The part was here in record time. We ordered it on Sunday, it shipped out on Monday, it arrived on Tuesday and we were back in operation! Thanks for a really smooth repair experience!
Was this helpful?
Thank you for voting!
large burners not working
0 of 2 people found this instruction helpful.
  • Greg from Versailles, IN
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Read instuctions first Turn breaker off to stove or unplug to be sure. Remove burner and drip pans. Remove scews holding socket in place if you are doing more than one make sure you keep in same location. Raise cook top untill supports latch in. Assemble plug it comes with two types holder compare to your plug. cut wire to old plug so yo u have enough wire to connect back with new. Strip wire back and place shrink tubeover wires wire nut together heat with a lighter or heat gun then do remaining plugges. place back in cover and replace scews. make sure wire are not to long to get under burner when cook top lowered. Lower cook top and clean burner plug ends with a little sandpaper to make sure they make good connection. replace pans and burner. turn on breaker or plug in stove making sure the burners come on when turned on good luck g.d.
Was this helpful?
Thank you for voting!
2 of the small burners just fell apart
1 of 5 people found this instruction helpful.
  • Janice M from Ocala, FL
  • Really Easy
  • Less than 15 mins
I just installed the new burners into the proper place and they fit This was very easy to order. Just had to find the model number which the web site told me where to find this. I am very satisfied with the service Thank You
Was this helpful?
Thank you for voting!
replace burner coil connector
0 of 2 people found this instruction helpful.
  • dicky from mcrae, AR
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Cut the two wires approx 1 inch behind old connector and removed one screws to remove old connector, stripped approx 3/4 inch off the wires and connected them to the new wires on the new connector with wire caps and shrink wraps which came with the new connector. Replaced the old screw with the new screw and the job was completed. Be su re and disconnect power before starting!!
Was this helpful?
Thank you for voting!
hinge broken again
0 of 3 people found this instruction helpful.
  • Russ from Milford, NE
  • Really Easy
  • Less than 15 mins
  • Screw drivers
r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.
Was this helpful?
Thank you for voting!
Baking element overheated and split into two parts.
0 of 3 people found this instruction helpful.
  • Derek from Gilford, NH
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
First removed 2 screws holding in element housing at the back of the oven. Pulled element out and disconnected wire leads from the the element connection points. Reconnected leads from new element, pushed back into the back of oven and rescrewed into the oven housing. Done, very easy.
Was this helpful?
Thank you for voting!
Door gasket gotten hard
0 of 7 people found this instruction helpful.
  • Richard from Pocomoke City, MD
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I took oven door apart and replaced old gasket with new one.
Was this helpful?
Thank you for voting!
Oven door hinge broken
  • Sherry from Mountain Ranch, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Discriptions provided by others in this section made it easy and there is little additional insight I can add. The part was delivered the next day. I don't reply to these requests for comments, as providing what I paid for is the expectation. But, this outfit did a good job.
Was this helpful?
Thank you for voting!
electric surface unit not working
  • vincent from Martinsville, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers
After turning off circuit breaker to the stove, I removed all surface units , removed the 4 screws holding the top and lifted up. The plug in was burned out (the wire was burned). Look at the old plug-in so as to be able to match the new one and insert the pre- crimped end of wires into the block and the block into the metal holder that matches your old one. (The kit comes with 2 different metal holders)After this, cut out the old wires and wire nut the new wires with the stove wires. Put shrink wrap protector on the wire nuts and heat to shrink it tight.attach the block to the stove top and wa la its done. Very easy.
Was this helpful?
Thank you for voting!
one burner that would not heat and others that would not out out much heat
  • Charles from Villa Ridge, MO
  • Easy
  • 30 - 60 mins
  • Screw drivers
I noticed that one of the burner blocks was completely burned and the others were corroded. I ordered blocks for all four burners. Installation was easy except for one block. The screw holding the bracket to the range top was completely corroded in place. I used a correct size easy-out, which is a left hand tap and drill, to remove th e screw. That took about five minutes, including tracking the easy-out down in one of my many toolboxes. The entire replacement of four blocks took about one and a half hours. Stove top cooks like new on all burners! The part kit had all the right parts and they fit like a glove!
Was this helpful?
Thank you for voting!
All Instructions for the EHS345-OF
106 - 120 of 156