ECKMF63 Whirlpool Ice Maker - Instructions

after reading reviews on changing the control module I decided it couldn't be very difficult. I was rewarded because it wasn't. It took less than 20 minutes to change the module. At first I was concerned because the wheel did not start turning as soon as power was connected. I discovered this is normal and 30 minutes later the icemaker ... Read more was making ice again. Simply remove the 3 screws, carefuly pull the module away from the shutoff arm, and pull it out. putting the new one in is the exact reverse. You just have to realign the ejecter cam in the icemaker with the new module so it slides right in.

After reading the stories on your site, I figured it had to be the motor control. Easy to take off, but had to take the tray off the freezer wall to get the ice out. Once I did that it was a piece of cake. Now I have ice (and vodka tonics...).

Replaced the valve and cleaned all the coils at the same time. The ice maker is spewing out ice. Wife is happy again.

Removed old water valve on bottom right back side of fridge installed new one which actually took less work

Followed Video Instructions

Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line

Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fi ... Read more tting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

First I disconnected the refrigerator. I snapped off the service door. taped closed the auto.door shut off located on the left side wall. the unit just pulled out,
disconnecting the power source, removed the plastic cover, unscrewed (3) screws and reattached the new unit . i reconnected the process in reverse.
if i had repairma ... Read more n do this it would have cost twice as much .

Did not have to remove the complete ice maker. Only the front part that housed to motor assembly. Two Clips removes to cover and three screws removed the motor unit and the rest was in reverse. No wires to disconnect or connect. It just plugs in to unit. Works great and cheaper than from Sears Parts Direct shipping cheaper also. Will buy ... Read more from Part Select again.
Thanks, Ron

The plastic fill cup part is also used to hold one end of the wire “one/off” switch that is manually activated or activated when the ice tray is full. This wire piece fell out because one end, that is part of the plastic fill cup, broke off. The wire switch was fine.

The video demos show you exactly what to do. The repair man ... Read more showed me a trick to speed up the testing process. The trick is to insert a wire jumper cable to actuate the ice maker and make it rotate. But this isn’t necessary.

Hardest part of this fix is emptying the freezer (bottom with a slide out door) and removing the door.

Why this part is so expensive is beyond me. But I’m happy it was available for a 24yo fridge that still works!!

We replaced this part 5 years ago, so we considered ourselves "experienced" at this particular job. We followed the video at your site and after some sticky removal parts, we were able to put the new motor in and finish putting the freezer back in its original shape. After a few worried hours, we again had ice. The video was easy to fol ... Read more low and we couldn't be happier. Thank you for saving us hundreds of dollars.

removed the white plate, unscrewed 3 screws and replaced the part.

Ordered new single outlet water valve, received in less than two days. Removed old one, and the repair pretty much feel in place. Instructions were there as a backup. ........ Just curious if the connection from the water source to the valve outlet connection could b a quick connect just the like the water line going directly to the ice ... Read more maker. Gregg in PA.

Watched the video...easy!

I don't know how he did the repair, but he told me it was simple, and I know it saved us a lot of money! Thank you for your excellent help and the delivery was like overnight!!
Submitted by
"The Wife"