EB3000CK2 (Type AVIN# GCBUT-1000001-9999999) Honda Generator - Parts

This is a genuine Honda replacement spark plug. It is sourced directly from original equipment manufacturer and it is sold individually. It is designed to ignite the air fuel mixture by the spark. If spark plugs are not checked with regular services, cleaned or changed when necessary, they can cause problems to occur with the engine. Replacing it you should only need a spark plug socket.

This is an OEM spark plug designed for engines to ignite the air-fuel mix inside the combustion chamber. This plug is white and silver and made of metal and ceramic materials. Over time the spark plug can become fouled due to a range of reasons including a poor air-to-fuel ratio worn piston rings carbon-build-up and general wear and tear....Read more You can clean a lightly worn spark plug with fine sandpaper and carb cleaner and re-install but generally you are going to have to replace this part often and it is better to replace a fouled plug than try to clean it. If your spark plug is in bad condition you may experience a missed start or a no-start situation. If the engine has 2 or more cylinders you can pull the spark plug wire off to see if the RPMs are dropping due to a miss. On a single cylinder a malfunctioning spark plug is more likely to cause a no-start issue. When replacing the spark plug be sure you torque to the manufacturer specs. Most customers found this repair easy you will just need a spark plug socket.

This genuine OEM oil filler cap assembly is part of your lawn equipment, found commonly on the top or side of the engine. It covers the oil fill hole on the engine so that oil does not spill out and impurities do not get in. A broken cap may be visibly damaged and will not properly seal the oil fill hole. If you do not replace it, the oil...Read more may become contaminated with dirt, reducing the lifespan of your engine. To remove the cap from your machine, gently grip onto it and rotate it counterclockwise. You can lift the cap straight up afterwards. This part is sold individually.

This is an authentic manufacturer sourced replacement part designed for use with Honda engines. This carburetor gasket provides an air tight seal between the carburetor and the insulator. Over time gaskets tend to deteriorate and would need to be replaced. It is made out of compound material and it is sold individually. You would need a screwdriver to replace this item.

It is a genuine item that is supplied by the original manufacturer for use with Honda engines commonly installed on a variety of lawn and garden equipment. This is one of the flange nuts that are utilized to secure the exhaust manifold. A flange nut is designed to provide a tight fit and resist loosening. Replacing it is a simple task tha...Read moret should only require a wrench to remove and secure it. To ensure the correct location, please refer to the diagrams of your model. One durable metal nut-flange is included.

This rubber fuel strainer cup gasket, found in your garden equipment, distributes pressure and creates a seal between the fuel strainer cup and the carburetor so that fuel does not leak. If it is broken, you will notice fuel leakage or a gas smell, and your engine may sputter or have difficulty starting. Unattended fuel leaks not only was...Read morete fuel but also pose a fire hazard. When removing the gasket, make sure that your machine is shut off and has cooled down. Consult your instruction manual to locate the fuel strainer cup, remove mounting screws and clips with a screwdriver, twist the cup slightly, and lift it away. Peel off the old gasket carefully. It is important to be aware that this authentic OEM replacement part is sold individually.

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. This is an identical replacement for a missing or damaged seal for the valve stem, please refer to the appropriate diagram of your model for the correct location and applica...Read moretion of this hardware. It is a high-quality component is made of durable rubber and is sold individually.

This item is an authentic OEM part which is made for use with Honda engines commonly installed on a variety of lawn and garden equipment. The clip is utilized to secure the fuel tube. If the clip is damaged or is missing, this will provide an identical replacement for a missing or a damaged component that was installed on a new unit. Chec...Read morek the diagrams of your model for the exact location and the correct application of this hardware. One durable metal clip is included. You may need pliers to secure and remove it.

This is an original replacement part manufactured for use with Honda small engines. The starter rope is pulled to engage the flywheel to start the engine, and the rope recoils back into the starter when the rope is released. The starter rope is sold individually, please see model diagram for associative parts.

This item has been sourced from the original manufacturer, and it is intended to be used with small engines from Honda. The metal spring links with the starter pulley and is used to recoil the roper back around the pulley after the rope is pulled. This item is available as an individual replacement part.

It is an identical replacement for a missing or a faulty item that is supplied directly from the original equipment manufacturer for use with Honda engines commonly installed on lawn and garden equipment. This is a replacement cap-fuel with a metal mesh filter on top, it will help to catch any large contaminants from the fuel. Please make...Read more sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.