EB22DKXWW01 Whirlpool Refrigerator - Instructions

This was really easy to do thanks to comments posted on the Partselect web site and the instructions included in the package. I removed three screws, unplugged the wire harness using a small screw driver to "unlock" the harness, removed the old ice maker assembly from the freezer, and reversed the process with the new assembly. Saved th ... Read more e valve and other parts for future use. The new unit started making ice within an hour or two. Very cool!

Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.

We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing

Removed the existing broken end cap, and replaced it with the new one. Installed shelf securely back in fridge. Easiest repair I've ever done. Less than 5 minutes. I wish everything were that easy.

I removed the broken end cap and then I snapped the metal shelf onto both end caps and replaced the shelf.

I really must say that dealing with PartSelect was exceptional. It took about three days for me to get the part and, prior to that, it was very easy for this sidewalk fixer to locate the correct part on their website. ... Read more Thank you for your excellent service.

Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great ... Read more !

removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.

I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.

Ordered new fan motor on line took out old motor and replaced with new one

first confirm that freezer is cold. if is frozen solid it needs to be defrosted. take the freezer items out,take shelf out, bottom cover, 2 screws. then ice maker, 3 screws and unplug wires. then back panel 2 screws. In refrigerator compartment were the controllers are located, look under it you will see 1 hole, insert a flat end screw dr ... Read more iver and turn clockwise till it stops. this action will turn on your defroster, also the compressor will stop. is the heater melting the ice? if so soak up water and clean tray, use hair dryer in drain hole to aid in the defrost, check tray under fridge and if its dry keep defrosting. it should take half an hour. now take the flat head screw driver and turn the defrost timer clock wise out of defrost mode a quarter turn or so. the compressor should come back on, soon after the fan in the freezer compartment should also come on. this steps lets you no that the defrost heater works, fan works and drain hole is clear. if its defrosted place parts back in the reverse order. if not defrosted replace heater or mother board. in refrigerator compartment were the dials are located their are 2 screws, one on the left and the other on the right side take them out, the cover will drop down, you will find wiring schematics you will need them to install defrost timer. is timer making ticking sound? if no replace timer. new timer will be different from original so follow instructions that come with it. timer is above were the hole is located. the plastic hold downs will break when you try to take them off, unplug fridge, lift timer out and remove from wire harness. the new timer has a black wire that slips over either 1 or 2 depending on color of wire on the wire harness. check schematics. some silicone adhesive will keep unit in place, ad some into the plastic shaft prior to installation, plug wire harness return wiring instruction along with new one inside of cover, plug in fridge, turn defrost timer clock wise with flat head screw driver making sure that you hold timer from above so it wont move. did compressor come on?. put all paper work inside of cover before installing cover

I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.

When we got the part, we read the instructions, which were easy and very clear step by step. Taking the old part off took most of the time, it was attached a little differently than was described in the video and the instructions for the part. Once we detached that, the replacement part went in very easily and quickly. It took a short w ... Read more hile for the cycle to start, we were actually a little worried that it wasn't going to work. Then it started cycling. After the first day the freezer had started icing up, we took a blow dryer and melted it and waited. It hasn't started freezing up again. The refrigerator is keeping the proper temperature and the freezer is also working properly, it's been a week. We seem to be obsessed with going out and checking to see if it's working but I think it's a success. Doing this ourselves only cost $26.00. A huge savings if we had hired someone else to repair it for us. We will definitely choose this option with any other appliance that needs repair. It was easy and simple to find the correct part thanks to the website. And the video tutorial was very informative and helpful.

replaced ice maker with recommended add on kit. easy to replace exact replacement. used this company for washing machine part. parts correct both times.

Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl ... Read more aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)

Unplug Dryer. Remove 2 5/16in hex screws from lower panel and remove panel.Remove 3 5/16in hex screws attaching lint duct. Remove 8 1/4in hex screws attaching blower housing. Remove 2 1/4 hex screws attaching thermostat to blower housing. Using adj. wrench on back of motor shaft nut to hold, loosen fan assy. w/ 7/8in socket. Remove 3 5/16 ... Read more in hex screws holding fan housing to motor mount. Remove 2 5/16in hex screws holding housing and motor mount to base floor. Push belt pulley wheel up enough to loosen belt and take off rear motor pulley. Motor w/mount can be slid out bottom for replacement [wires are layed toward front].Using 6in flat tip screw driver press down to unlock front & back motor bushing holddown clamps. Pinch electrical wire connector ends to pull off old motor. Remove and Install new motor, reversing steps. Belt replacement [suggested w/new motor] requires removal of 2 5/16in screws to lift/remove door w/front panel [disconnect door switch wires upper right rear corner].Remove 4 5/16 screws holding front bulkhead. Once bulkhead is pulled up and off, allow front end of drum to sag and rest IN PLACE [removal not required to slip old belt off and install new belt]. Note belt location point around drum. Slide new belt on. Reinstall bulkhead and panel/door [Don't forget door swich wires]. Adjust belt into position and push spring-held belt pully up to allow looping of new belt around rear motor belt pulley. Complete w/hand turning of drum to ensure belt is aligned and feeding properly. Reinstall lower fan housing/covers/thermostat,etc removed for motor installation.