E23CS75DSSF Electrolux Refrigerator - Instructions

Had help with one person,to lift the door.But the part was easy to install.

snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

simply took the screws out of the top of the door(after first emptying the door), picked it up off the bottom support and laid it on the counter. Used a needle nose pliers to remove what was left of the bottom bearing and replaced it with the new bearing. Placed it back on the support and put the top door mount back where it belonged. replaced the plastic hinge cover and it was as good as new. Really very simple.

Installed new valve.There are several pieces of tubing coming off of the valve. Pay close attention to where they go. Color coordination is poor on the new valve.

I watched your video on how to do the procedure and followed it, step-by-step. It worked like a charm. When I took the crisper drawer and runner out of the refrigerator, I noticed that the lower drawer support had broken as well. So, I have ordered 4 to have a few on hand and will repeat the process when my new order arrives. I'm very pleased! Thank you very much.

The defrost thermostat kit is located in the freezer side of the refrigertor. I turned off the electrical breaker for the refrigerator. I began the project by removing all the frozen food on the lower half of the freezer. I removed the racks and 3 rails on both sides using a cordless drill with a 1/4" socket and located panel. The panel had 4 1/4" screws holding it to the back of the freezer. I removed all screws and the panel came out easy. I located the defrost thermostat and with some wire cutters, I cut the wires. I connected the the new defrost thermostat with wire connectors and reattached it to the copper tube I removed it from. I put the panel back on along with the side rails and racks.. This project was very easy.

take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .

used nut driver to loosen 2 screws partially. slightly lifted up ice-maker and pulled out. unpluged the ice maker from socket and removed. i timed myself. 4 minutes to take out and replace new one. glad i did not call repairman. wife skeptical at first until we started hearing the ice fall.

I watched the do it yourself video which helped tremendously. My husband was busy so I was able to do it myself.

I changed the valve but still no ice, changed the filter also. think it was just froze. could have saved me 70 bucks

Purchased a replacement part only to find the new part had push on fitting and my part has screw on fittings. Went to Youtube where Partselect had a video on how to replace the part from screw fittings to push on fittings

Fortunately, this was not hte first time to do a repair on the through the door dispensers. I turned the unit off and removed the door tray (slides out) to expose the screws for trim removal. When that is removed, you remove the circuitry and then remove the actuator and spring. It was difficult to get the new actuator in place. the "stop" which holds it in pace is not forgiviing! And that is being mild. (I remember a few explitive delitives I thought wer gone foreever! I reconnected the circuit to the panel, replaced the panel, and the tricky part was to reinsert the water hose into the dispenser hole. Good luck. When that was in, the entire unit was reeturned with the four screws. The front trim panel was replaced with four screws, and the slide in drip tray was slid in. Job done, and the power was restored. Thank goodness I had some long hemostates to control the reinsertion of the water tube!

took old valve off one peice of it was broke off from freeze replaced it with new valve all but one conection was quick connect electric connections were color coded quick fix works fine thanks Gary

Pushed the "release button" and took out old filter. Pushed the new filter in place until it 'snapped in place.' Then ran the 'water' until it stopped spitting out air.

The changing of the water valve was pretty straight forward. First shut the water off to the ice maker, then pull the refrigerator out. Once that is done, then I removed the cardboard covering with a cordless drill, loosened the screws that held the water valve in place. The water valve assembly is colored coordinated so disconnecting and reconnecting the lines to the new valve assembly was pretty easy. Reattached the cardboard covering pushed refrigerator back and place turn on supply line and waited for the ice maker to fill up. After several cycles on the ice maker I made one slight adjustment on the ice cube size behind the cover of the ice maker. Total time one hour, then waiting for the ice maker to cycle a few times to ensure all was working properly.