DW362K (Type-1) DeWALT Saw - Parts

This brush and holder assembly is a genuine Dewalt replacement part, not aftermarket or generic. _b_This item is sold individually_/b_. As pictured, this item includes everything you need to replace a brush in your power tool. The brush, holder, terminals, and spring are included and ready for installation. If you only need the carbon ...Read morebrush and not this entire holder assembly, you can purchase the brush separately (see the 'Related Items' section below). This brush and holder is compatible with the tools listed below, but it is not guaranteed to fit any other power tools. It is advised that you replace both brushes only if you think all you need is one.

This is an OEM part sourced directly from the manufacturer. The screw is found in Craftsman circular saws. This is a metal part, used to hold other components to the spindle assembly. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 14 Gauge • 10 Feet Long

This Genuine OEM carbon brush is an essential replacement part designed for use with a variety of DeWALT and Black & Decker saws. Sold individually, this high-quality component is made to conduct electrical current within the motor, enabling efficient power transfer and tool performance. Over time, carbon brushes naturally wear down due t...Read moreo friction and electrical contact, which can lead to intermittent motor issues or failure to start. Measuring 3/4 inch in length, 1/2 inch in width, and 1/4 inch in thickness, this brush is built to original specifications for a precise fit. When replacing carbon brushes, it’s important to also inspect the motor’s armature for signs of burns, cracks, or other damage, which may indicate a more serious issue. A hex key or screwdriver may be required for installation, depending on your tool model.

This is a genuine replacement outer blade clamp specially made for circular saws. This part helps to secure the blade to the unit. A wrench would be needed to remove the blade bolt when replacing this clamp. It is made out of metal and it is sold individually.

This cord protector is a genuine DeWalt replacement part and is sold individually. Cord Protectors are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard.

This replacement screw is a high quality hardware that is specially manufactured for use with Dewalt, Black and Decker and Porter Cable power tools. It is a authentic OEM sourced item that has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.

It is a genuine replacement screw that is sourced directly from original equipment manufacturer. This is a standard hardware that has multiple uses depending your tool. For correct location and use of this screw, please check appropriate diagrams. This torx screw is sold individually.

This is a genuine replacement part sourced from the original manufacturer for use with circular saws. The special metal screw can have multiple applications, but is most often used to secure the guard lever to the lower guard. This screw is sold individually. This screw is included with the complete lower guard, part number 388524-00

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with circular saws and hammer drills. The special retaining ring is commonly used to secure the fan to the armature's shaft. This item is available as an individual replacement part, please see illustrated diagram for associative parts.

This is a genuine manufacturer sourced replacement handle set. It is specially designed for Dewalt circular saws. This handle houses the trigger switch and provides a comfortable grip for safe operation. It is made from durable yellow plastic and it is sold individually. Please note, the hardware to attach it and the switch are all sold s...Read moreeparately. To complete this repair you will need a screwdriver. • Unplug the saw • Remove the handle screws • Separate two handle halves • Disconnect switch wires and remove the switch • Secure the switch in the new handle set • Attach wires to the switch • Secure the new handle with the hardware