Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer would not spin
The design of my dryer is a bit different from the video on PartSelect - but it is very close. And if you watch the really good video on PartSelect plus a few others on Youtube you can figure out how Samsung in general designs the different components. You can fix this yourself definitely.
Cost of part to fix - about $50. Repairman - didn't even ask. Would probably be $300-400. Cost of replacement $1,000.
I rated the repair "A bit difficult" only because this is the first time I have ever repaired an appliance. If I were to repair this one again, I'd rate it as Easy.
I'm really thankful for the PartSelect video. This makes DIY repairs possible.
I'll make this quick. To access the motor you need to take half of the drier apart. I cut a access door on the side where the motor is with a small electric saw. It gave me clear access to the motor. You still need to take the front cover off to remove the blower wheel . One more thing, make sure to have the belt back on when testing, otherwise the motor wont start. It took me about an hour and 15 minutes
Removed top of dryer, control panel, front (door) panel. Removed screw holding heating element and housing assembly in place, and removed wiring connections. Attached wiring to new heating element and housing assembly, installed screw to hold in place, replaced front (door) panel, control panel, and top of dryer.
The (front-load) dryer was noisy and eventually slowed down but was still heating.
I removed the dryer top and saw that the belt was intact. (I had suspected the belt or something stuck in the exhaust fan or somewhere.) I watched a few youtube videos and took off the rest of the top plates and front door and inner structure that held the barrel. After i inspected and cleaned out the fan blades and exhaust areas, I looked at the pulley rollers (motor and idler rollers). The idler roller looked a little melted and chewed up. I replaced it with the new assembly. Also replaced the belt. Putting the barrel and new belt back on was harder for me than the videos indicated because the spring was very tight and the area to put my hands was small and didn't give me enough leverage. I eventually got someone to give me the third hand pulling the idling roller a little further over and the belt was back on. It didn't take me long to put the whole dryer back together. It is running fine now.
These are not instructions as much as warning that although it is a one-person job, the idler pulley assembly is not as easily manipulated with the barrel there. Doing the fix was straightforward: one screw holds it in place. The men in the videos seemed to have no problem with easily replacing the belt, but I needed help with the tight spring. Perhaps now that I've done it once, I could figure out how to reach around the barrel and yank the roller enough to replace the belt, but with the extra hand it took seconds and was super easy.
high limit thermostat and heating element were bad.
I would like to direct the attention to PartSelect instead of my repair. They were awesome in helping me to get my parts. I had called, a few minutes after the deadline for overnight shipping, the gentleman helping me, pushed the order through and I got my parts the next day, allowing me to repair my dryer. I have ordered several parts, for several different appliances, (all Samsung) and PartSelect has always come through for me. Excellent Customer Service!! P.S. Don't buy Samsung appliances unless you want to get good at repairing them!
Ordered part on 8/24/22. Received wrong part twice now. It is 9/10/22 and I am waiting for the third. Right part number on package but it contains the wrong part. Beyond mad!
I pretty much followed the provided videos, but didn't remove the drum. That seemed a bit much. I was able to get the heating element out, and replace the Thermal Fuse and Thermostat. Dryer runs and heats like a top now!
I still had to take it apart there was a small sock stuck in the fan that blowes the lent out my wife left the lent filter out one time. Your video was a great help. I'm a mechanic and it was easy thanks Anthony Ratto Tulipbike82@aol.com
IMPORTANT!!! Unplug the unit first!! 1 - Remove two screws on the back of the top of the unit. Pull back a little on the top to release it from underneath the control unit on the front of the dryer (the piece with the dial and buttons). 2 - Remove the four screws from the control unit. They are located at the top of the dryer. Pop off the control unit - don't worry about breaking any wires as there are none. 3 - Remove the front of the dryer by removing the four screws that are NOT used for the door and door latch. I had also removed the door latch and door but I don't think it is necessary to remove them. The front will swing out from the bottom where you can unhook it and remove it. 4 - the heating element is located on the front of the unit, bottom right. Either draw a diagram of the wires or take a picture of them with your cell phone. Smart phones are great for this as you can zoom the picture if necessary. Remove the wires (they just push on but it may take some effort to get them off). It's either one or two of the wires that are not part of the wiring harness and they go from one part of the element to another so don't get excited if these wires fall down - you haven't done anything wrong, they are just loose. The one screw in the front holds the element in (the back of the unit just rests in that hole). Remove the screw and pull the unit out. Put the new element in, hook up the wires before positioning the element. Put the screw back in that holds the element and put the rest of the dryer back in the reverse order.