DOP48C96DLS ((DA)(0001)) Samsung Range - Parts

This door switch, also known as a safety switch, is a genuine OEM replacement part for microwaves. It is a safety mechanism that sends signals to the microwaves control system, telling it when the door is open/closed. This ensures that the microwave only operates when the door is securely shut and switches off as soon as the door is open....Read more Over time, this switch can become worn out or damaged. A faulty door switch can result in failure to switch the microwave on/off, lack of heat, and running with the door open. To confirm that the door switch is faulty, use a multimeter to test for electrical failure. To remove the faulty switch, disconnect the wiring connectors and take note of where they are positioned. Place the new switch in position and reattach the wiring connectors to the appropriate terminals and close the microwave door to check that the switch engages appropriately.

This is a high limit thermostat designed for microwaves, ranges and ovens. Made of plastic and metal, this thermostat is designed to open the electrical circuit for your appliance when it reaches a specific internal temperature. In some cases, high limit thermostats can become defective and if your appliance will not turn on, or has a spe...Read morecific error code, it must be replaced. This thermostat is a genuine OEM part that is sold as an individual part and can be replaced by disconnecting the appliance from the power, and accessing its panel, usually located near the bottom of your range, or wherever the heating element is located. Reference your user manual for exact location and replacement instructions.

This rubber cushion is supplied by the original manufacturer and has a shaft approximately 1 inch long. The cushion acts as a layer of protection between the oven door and oven frame/cavity. It prevents heat from escaping and protects the oven door and frame from abrasion and damage. If the rubber cushion becomes brittle or loses its elas...Read moreticity, you will likely notice heat escaping from the appliance, uneven cooking, as well as increased noise, and instability when opening or closing the door. Depending on your appliance model you may need to lift the top oven panel to access the cushion. Pull the faulty rubber cushion out from the oven frame and thoroughly clean the area where the new one will be placed to ensure a good seal. Press the new cushion into position and reassemble your oven to complete the repair.

This genuine OEM left-threaded convection fan motor is responsible for spinning the fan blade, ensuring even circulation of hot air within your oven for consistent cooking. It is typically located behind a removable cover at the back of the oven. Signs of a faulty motor include rattling, squealing, or slow and irregular fan rotation. Negl...Read moreecting to replace the motor can result in uneven browning or undercooked portions in your food. To remove the motor, you will need a screwdriver and a socket set. Consult your user guide for instructions on accessing the back panel of your oven. Remove the mounting screws and the fan cover, then the nut securing the fan. Slide out the fan and motor assembly from your oven. Remember, the motor is sold separately from the fan, so consider this when purchasing a replacement.

This genuine oven temperature sensor monitors the internal oven temperature and sends accurate readings to the control board, helping maintain consistent cooking temperatures and reliable oven performance. Replacing a faulty sensor can help resolve issues such as inaccurate temperatures, uneven cooking, overheating, failure to heat proper...Read morely, or temperature-related error codes. The sensor features a durable metal probe with a mounting bracket for secure installation inside the oven cavity. Installation typically involves disconnecting power to the appliance, removing the mounting screws, disconnecting the sensor wiring, and installing the replacement sensor. Designed for precise temperature monitoring, this OEM replacement sensor operates within a temperature range of approximately 32°F to 932°F (0°C to 500°C) and measures approximately 1,080–1,100 ohms at room temperature. Please be sure to test the part with an ohm meter before ordering to ensure the part is defective.

This hexagon nut cap, also known as a nut cover cap, is a nylon-insulated cylindrical cap with left-hand threads and a 4mm thread size, for counterclockwise tightening. It is sourced from the original equipment manufacturer for use in ranges and microwave oven combos. The cap provides added security to prevent the hexagon nut that it rest...Read mores on from coming loose during operation and causing component instability. Over time it is normal for the hex nut cap to wear down, become damaged, or for its threads to become stripped. To replace a faulty nut cap, use a socket or wrench to unthread it from the hex nut. Place the new cap in its position and secure it in place to complete the repair. It is recommended to replace the fastener at the same time for extended durability.

The Samsung Burner Cap - Small is a sturdy and durable component, perfect for frequent use in your kitchen range. Crafted from heat-resistant materials, it is designed to promote even cooking and protect your food. Essential for safety and reliable performance, this burner cap situates atop the burner head, providing protection from spill...Read mores and optimal heat distribution. Please ensure the range surface is cool before you install this product. Easy to fit and made to last, this genuine Samsung range surface burner cap elevates your cooking experience by ensuring even and safe heating.

This terminal block assembly is designed for use within various models of ranges and is sold as an individual OEM part without any other hardware included. Terminal blocks are responsible for receiving, managing, and distributing the power within an appliance. Electrical shorts or surges can cause this terminal block to overheat and melt ...Read moreand become inoperable, thus needing immediate replacement. If you smell melting plastic when operating your range, turn it off and disconnect it from power immediately and inspect this terminal block and all other electrical components. To replace this terminal block, disconnect your range from the power and remove it from the wall. Remove the back panel of the range and locate the terminal block, making note of its wire configuration. Unscrew the wires and the ground wire if there is one, and then do the same for the mounting screws. Install the new terminal block in the same position as the previous one, attaching all necessary wires as they were originally, before you reconnect and reposition the range.

This genuine OEM dual burner cap is a durable replacement part designed to sit on the burner head, protecting it from spills and debris while ensuring even heat distribution for consistent cooking results. Made from high-quality materials to withstand high stovetop temperatures, it helps control the flame area for improved safety and perf...Read moreormance. If your existing burner cap is worn or damaged, replacing it restores proper function and efficiency. Installation is simple—just position the cap securely on the burner head.