DM84KG Magic Chef Microwave - Instructions

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th ... Read more e help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

Unscrewed the cover of the microwave replaced the blown fuse with the new fuse, plugged in the microwave and tested all functions and everything worked fine. Thx for quick delivery.

First i removed the 3 phillips head screws from the back of the microwave,these hold the wrap around cover in place, then slid the wrap around cover off towards the back side of microwave, next from inside the microwave i removed 1 screw holding the front operating panel, this screw is located staight up from the push button towards the ... Read more top of the microwave, I pulled the panel out enough to get the broken push button out, then i installed the new push button,then reinstalled the operating panel then the wrap around cover, very simple repair saved a lot of money by replacing the part rather than buying a new microwave.

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that ... Read more is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Pryed face plate away from body and removed broken latch, replaced with new latch/release button (just sets in place) and pressed faceplate back into position. The beauty of all this is, I ordered this part on line, late on a Tuesday evening and had it in hand by Thursday afternoon!
Well done! Thank you!

unscrew microwave's cover,test the fuse which is located at top rear left side, the fuse is inside a plastic tube,if the fuse is burnout,just replace it.

Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!

Unscrewed back plate, and replaced bulb

The part was delivered at 5 o'clock and by 5:30 the repair was done.

Remove 3 screws on the back. Remove the outer shell. Remove 1 screw behind the face plate and then lift off the front face plate (this does not have to be completely removed for repair.

Remove the broke part. I then cleaned the area to remove al ... Read more l grime.

The new part slids into place. At first I tried ti fit it between the support posts and realized that one post goes on the insid of part and the other outside.

Replace all pieces and your done.

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. ... Read more Reassemble and you are done!

Removed damaged tray and broken pivot pin. Go to part select . Com. Locate parts trough schematic presentation and order parts. Parts came as promised and installed easily without tools.

remove 3 screws holding cover, slid cover to the rear, removed screw at top inside of control panel.
lift up control panel to release it. this exposed broken release button. noted position of release button. with finger pushed up part of door that extended inside to release door (what the broken part was suppose to do). also note t ... Read more hat the left side of the release button goes over the metal protrusion (small cut for to view placement). the right side goes inside the metal protrusion. reassemble and you are ready to go.

Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.