DM5K-7TS Magic Chef Microwave - Instructions

Unscrewed the cover of the microwave replaced the blown fuse with the new fuse, plugged in the microwave and tested all functions and everything worked fine. Thx for quick delivery.

First i removed the 3 phillips head screws from the back of the microwave,these hold the wrap around cover in place, then slid the wrap around cover off towards the back side of microwave, next from inside the microwave i removed 1 screw holding the front operating panel, this screw is located staight up from the push button towards the ... Read more top of the microwave, I pulled the panel out enough to get the broken push button out, then i installed the new push button,then reinstalled the operating panel then the wrap around cover, very simple repair saved a lot of money by replacing the part rather than buying a new microwave.

unscrew microwave's cover,test the fuse which is located at top rear left side, the fuse is inside a plastic tube,if the fuse is burnout,just replace it.

Pryed face plate away from body and removed broken latch, replaced with new latch/release button (just sets in place) and pressed faceplate back into position. The beauty of all this is, I ordered this part on line, late on a Tuesday evening and had it in hand by Thursday afternoon!
Well done! Thank you!

Using a flat-head screw driver, I removed the 1 screw from the small "door" on the back, upper right corner. Once the screw was removed, it allowed the door plate to "pop" open; exposing the old bulb. I removed the old bulb; replaced it with the new one. DONE!

Unscrewed back plate, and replaced bulb

The part was delivered at 5 o'clock and by 5:30 the repair was done.

Remove 3 screws on the back. Remove the outer shell. Remove 1 screw behind the face plate and then lift off the front face plate (this does not have to be completely removed for repair.

Remove the broke part. I then cleaned the area to remove al ... Read more l grime.

The new part slids into place. At first I tried ti fit it between the support posts and realized that one post goes on the insid of part and the other outside.

Replace all pieces and your done.

remove 3 screws holding cover, slid cover to the rear, removed screw at top inside of control panel.
lift up control panel to release it. this exposed broken release button. noted position of release button. with finger pushed up part of door that extended inside to release door (what the broken part was suppose to do). also note t ... Read more hat the left side of the release button goes over the metal protrusion (small cut for to view placement). the right side goes inside the metal protrusion. reassemble and you are ready to go.

Removed damaged tray and broken pivot pin. Go to part select . Com. Locate parts trough schematic presentation and order parts. Parts came as promised and installed easily without tools.

Screwed the new “$40” dollar light bulb back into the recessed socket. The new bulb is much smaller that the original bulb and much harder to get fingers into small area where the bulb went. After several try’s, I got it in.

I just lifted off the turntable, cleaned spilled food from under it, slipped on the gear, and replaced the turntable.

PartSelect's superb website made finding the model number and the parts diagrams for that model super fast and easy. From there, ordering the part was a snap.

My Dearest One removed the screws that held the part that covers the bulb; removed the old bulb, put in the new bulb and replaced the cover.
The whole operation took less than 5 mins.
Thank you.

First I had to remove the microwave from where it was mounted in a cabinet over the stove in the motorhome. Then I had to pry off the bottom part of the guard panel that surrounds the electronic face. Then the broken door release lever came out easily. It was easy to replace with the new one and then I tested it several time to make sure ... Read more it worked correctly and it does. I then replaced the guard panel and returned the microwave back to it's cabinet in the motorhome. DONE

1) Remove three screws on back of microwave, so you can slide the top cover back and remove it. 2) Remove the nut at the top of the control panel with a nut driver or wrench. Pull the control panel out enough to get to the door switch. You don't need to take the panel all the way off or unhook any of the attaching wires to the control pa ... Read more nel. 3) Remove the old door switch. It just sits in some guide grooves. There are no fasteners to remove. 4) Put the new switch into the same position as the old one. 5) Verify the door opens when the switch is pressed. 6) Replace front control panel and top cover. 7) Microwave one cup of water and fix yourself a nice cup of tea.

Took out The Three screws holding on the outter shell. Removed the screw holding on the front panel. Replaced the door release button. Put front panel back on. Then replaced the outter shell. Total time to do the repair was about 20 minutes.