DLL2980PD Hotpoint Dryer - Instructions

Unplug dryer and turn off gas to appliance. Remove small vent door front of dryer for access to burner assembly. Reach inside and remove all three wires attached to the valve. Using a backup wrench remove the union that attaches the 3/8" gas line to the burner assembly. Remove the two bracket screws holding the assembly. The entire burner ... Read more assembly can now be pulled out. Replace the faulty igniter by spreading the retainer clip and inserting the new part. Use extreme care not to touch the new igniter with bare skin...best to use a helper to assist holding the assembly while you insert the igniter. Then replace everything as you found it . Soap all gas fittings, plug it in and enjoy your dryer.

I watched Youtube videos on how to troubleshoot the dryer but I did not go through all the testing of the fuses and the heat sensor. I did not want to take the dryer apart if I didn't have to. I turned on the dryer and looked into the bottom grate and saw no glow from the igniter (it should be very bright) so I started there. (The Youtube ... Read more videos test the igniter last). Unplug the dryer. Turn off the gas. Pry off the grate. Unplug the igniter connector and set the multimeter to tone on continuity. There was no tone so it was bad. I used a flashlight that I put inside next to the gas valve to see. Remove the top flat cover on the burner assembly, 2 screws. (Had to do all this laying on my belly in front of the dryer. Very uncomfortable.) Remove the old igniter from the clamp. It fell apart as I took it out. Now the tricky part: The clamp is very tight and the igniter is delicate. I tried to slide it in from the top holding it between my index and middle finger and lining up the slots for the igniter 'wings'. I struggled with that until many-swear-words-later, I decided to slide the igniter in sideways. Put the 'wing' into the clamp's left side opening and then gently but firmly squeezed the 'barrel' into the clamp. It worked. Plug in igniter plug, put burner cover back on carefully without banging igniter, turn on gas, plug in dryer. Turn on dryer. Igniter should be very bright when it lights. It takes a little while to heat up the heat sensor that will open the gas valve and the burner should light.

Unplugged dryer. Removed access door from lower right front of dryer. Disconnected wiring harness to igniter. Couldn't reach retaining bolt with wrench or socket, but was able to spread igniter clip with fingers to be able to remove old igniter and then work new igniter into position without unbolting retaining clip - ultimately a tool-le ... Read more ss operation that could have taken 5 minutes. Reconnect wiring harness and reconnect power. Test dryer then replace access cover.

Took off the top cover then took off the front panel and installed the new coils on gas valve.

Make sure your power is off, When loosened the top and tilted back, the first thing I saw was the door switch, I guess I was just lucky I disconnected the two wires and checked it and it was bad. Got my new one from you and installed it. It has a ground terminal, which my model switch only had the two terminals. It working fine.I took the ... Read more bad switch apart and the one leg on the copper U shaped contact had broken off. The Belt I have as a spare.

the switch was stuck couldn't get the switch to pop out to stop the dryer when opening the door light inside also wouldnt go on. it only took a few min to take it the switch and replace the new switch the light now works also stops when opening the door it made my day easierhow easy it was to fix it. only take to use a pliers and screw dr ... Read more iver.

followed video direction ,pulled part ,compared to part on-line ,ordered part delivered in two buisness days and installed ,back in service .very simple and I will shop at your sight again and tell friends and family as well

I was disappointed that there were No Instructions included with the part. So I found a you-tube video that wlked me through it...Took off back of dryer, then the top, then the front to get to the igniter...could not pull out the part, so I had to reach in and replace it while it was in the dryer. It Works!

Researching on the web I thought the trouble might be lint buildup or trouble w/ one of the parts involved in spinning the drum. However I cleaned out all the lint and replaced the belt and idler pulley and this didn't improve the smell (drum bearing was fine). I then concluded the trouble was the motor. Running the motor w/o the drum ... Read more in place confirmed this was where the noise/smell was coming from. Replacing the motor was fiddly--I had to remove the clip holding the motor (pried the top w/ a screwdriver), wires (made a diagram so as to put back in same order, they were hard to get off--a pliers did the job), clamps holding the motor on the duct, the motor mount, the duct, the fan. Putting all this back together took a while (not hard just fiddly). Tested the motor w/out the drum in place and it sounded fine. Put the drum and back/front/top panels back and the dryer runs fine now. All parts came quickly and exactly matched the parts in my 1993 Hotpoint dryer. As others have said the pulley kit is not needed--these are included w/ the motor. BTW I am a 53-year-old lady. Thanks to all who took the time to write up their experiences--big help!!

What to do if you have a load of wet laundry at 23:00, the dryer won’t start, and you have no spare start switch.
Removed rear access panel and discovered the wire from terminal #2 (goes to heater coils) on the start switch had melted and disconnected. The start switch showed signs of overheating but not melted. Removed the switch an ... Read more d found the switch’s actuator button was jammed in the ‘in’ position (dryer won't start). The switch was a friendly one in that it was possible to disassemble it. Most switches today are molded/glued together, but this one could be pried apart. The contacts inside were still in fair condition and, after dressing them, the switch was reassembled. The actuator button had a burr that was filed off and the switch action worked fine. All of the 1/4" male QC contacts on the switch were cleaned with a wire brush. The burned wire was cut back about 6” and a new piece of 14ga wire was spliced in with a wire nut. A new 1/4” QC terminal was crimped to the wire and all wires were re-attached to the switch.
This fix would probably last for a long time to come, but I bought a new switch and installed it and will keep the old switch as a backup.
p.s. The load of laundry was dry by 02:00.