Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The lint dryer filter was not fitting in correctly so it sticks out a bit and while clothes are drying it was catching it and ripping/twisting and damaging all my clothes
33 of 40 peoplefound this instruction helpful.
Luciana from PRT WASHINGTN, NY
Very Easy
Less than 15 mins
I bought the whole dryer filter kit, but turns out I only needed the dryer filter and am very happy about that. No tools necessary I just slid it right in. It fit perfectly and I no longer have anxiety about my clothes coming out ripped.
Was this helpful?
Thank you for voting!
Former lint trap would catch clothes in dryer and rope them together
13 of 13 peoplefound this instruction helpful.
Brian from LOCKPORT, NY
Really Easy
Less than 15 mins
Pulled out old lint trap and installed new one in its place
Was this helpful?
Thank you for voting!
Lint filter and cover guide melted which was ripping up some clothes
15 of 21 peoplefound this instruction helpful.
Kevin from FARMINGVILLE, NY
Very Easy
Less than 15 mins
Screw drivers
Just unscrewed four screws. One piece stays behind which is a sensor then pull up on it, put it back in the same way, put the four screws back in and it was done.
I didn't get to do the repair because despite the model number and the picture being exactly what I needed I was shipped the wrong part and basically told by pets select to shake it off that's your problem not ours.
Original lint housing has damage that causes clothes to get caught and tear up
9 of 10 peoplefound this instruction helpful.
Justin from VANCOUVER, WA
A Bit Difficult
30 - 60 mins
Screw drivers
Able to complete install but the lint housing does not allow the lint screen to slide down completely due to the housing lacking the appropriate cut outs/notches. The slit becomes too narrow for the lint screen so it protrudes from the sides. The delivered product does not match the image on the item description, which shows the proper cu
... Read moret outs/notches that should fully accommodate the lint screen. I'm having a similar experience with this reviewer:
John S - February 14, 2022 Verified Purchase Lint screen housing The housing will not allow the lint screen to set completely down because the housing lacks the proper cut outs causing the lint screen to set 1-1.5 inches too high. I was able to cut out the required notches in the plastic so that the lint screen would fit. The picture shows the proper notches but the delivered product didn’t have the notches and does not match the picture.
Will return the item and keep searching for the correct lint housing.
Read less
Was this helpful?
Thank you for voting!
Manufacturer has redesigned the filter and housing, so you have to get the updated parts in a set.
7 of 9 peoplefound this instruction helpful.
David from ALEXANDRIA, VA
Very Difficult
More than 2 hours
Screw drivers
This has taken days to get the updated parts from another major international supplier. You can't just buy the screen or the housing - you have to get an updated set. Unfortunately they were not immediately available from PartSelect.
Was this helpful?
Thank you for voting!
The lint screen had a broken edge
5 of 5 peoplefound this instruction helpful.
Vivien from CARLSBAD, CA
Very Difficult
Less than 15 mins
The lint screen that this company sent was 3x too large. I called to return/exchange it. No one available - go to customer service. I went to customer service and entered my email address and the order number (while I was looking at the original order1). The email and order number could not be found.
I am still wai
... Read moreting to hear from someone from the company to get a RMA and return label! Will NEVER use this company again. Vivien Joebchen
Read less
Was this helpful?
Thank you for voting!
The mesh was ripping away from the frame on the dryer filter
3 of 3 peoplefound this instruction helpful.
Carla from CHARLOTTE, NC
Very Easy
Less than 15 mins
Ordered a new one and installed it in a matter of seconds. Not difficult!
Was this helpful?
Thank you for voting!
None
4 of 6 peoplefound this instruction helpful.
Ernest J from Columbia, SC
Very Easy
Less than 15 mins
When manufacturer confirmed the part would fit without an adapter, it was the easiest DIY task ever undertaken.
Was this helpful?
Thank you for voting!
The dryer's lint filter was cracked.
3 of 3 peoplefound this instruction helpful.
David E from SAN ANTONIO, TX
Really Easy
Less than 15 mins
I put the dryer information into my browser and found PartSelect had the exact replacement part I needed. I ordered the part and it came is just a few days. I removed the part from the excellent packaging, removed the cracked lint filter from the dryer, replaced it with the new lint filter and done! Among things I've successfully r
... Read moreepaired, this was the easiest and best job I've ever done. Quick, Easy and painless. Thanks for asking!
Read less
Was this helpful?
Thank you for voting!
Cracked lint filter
2 of 3 peoplefound this instruction helpful.
Richard from MADISON, AL
Very Easy
Less than 15 mins
Simple replacement
Was this helpful?
Thank you for voting!
a piece of plastic broke by the lint trap
Jason from Davenport, IA
Easy
Less than 15 mins
Screw drivers
with expert precision
Was this helpful?
Thank you for voting!
One corner of th elint filter kept sticking up and catching clothes on it.
Paul from Grosse Pointe Farms, MI
Really Easy
Less than 15 mins
R&R new lint filter.Old filter appears to have been made improperly and the out frame was warped raising the cormer that kept catching the clothes.
My Orders
