DLEX7880WE (00) LG Dryer - Parts

The sensor controls the temperature in your dryer and will turn off once your clothes have reached the desired dryness level. If you notice that your dryer is not giving off enough heat to dry the clothes or is taking too long to dry, this may indicate that a repair to the senor is required. To access this part, you will need to remove th...Read moree front bulk head. To remove this, you will need to remove the screws securing the top. Uninstall the screws that support the control panel and lift. Remove screws holding the support bracket in place so you can detach this piece. Detach the wire harness and remove the wire, then set the bracket aside. You will now open the dryer door and release it by taking out the bottom two screws. Disconnect the wire harness and moisture sensor wire harness, remove screws from front bulk head, and remove screws that secure the duct housing. You should be able to completely remove the bulk head. You will find the sensor underneath the lint filter grill, which will also need to be removed.

The thermostat is a part for your dryer, and it is roughly 1 inch long by roughly 1.5 inches wide. The purpose of the thermostat is to measure the temperature of the air inside your dryer drum. As the air is being measured, it will turn the heat on or off in order to maintain a stable temperature within the drum. The most common reason yo...Read moreu would need to replace your thermostat is if your dryer is not receiving enough heat, or any heat at all.The tools you will need to complete this repair include a Phillips screwdriver, and a flat-head screwdriver.

This dryer thermistor temperature sensor helps monitor and regulate the temperature inside a dryer. This part includes the wire harness. If your dryer overheats, does not produce enough heat, or takes too long to dry, then the thermistor might be defective or damaged. This can cause a fault code and could begin either prolonging or shorte...Read morening drying time. As a safety precaution, make sure to unplug the dryer from the power source before beginning this installation, and wear gloves to protect your hands. Refer to the installation instructions provided by the manufacturer for further guidance.

This genuine OEM felt gasket provides a cushioned seal between the inner tub of your electric dryer and the rear panel. It prevents your clothes from getting snagged and helps in heat retention. You will find it around the circumference of the drum. The most typical reason for replacing the felt seal is when it becomes worn. It is importa...Read morent to note that this rear seal is sold separately from the front seal and the adhesive needed to install it.

This genuine OEM filter guide keeps garments from exhaust air duct and lint screen inside the dryer. The filter guide is made of high quality plastic and is approximately 15 inches long by 3 inches wide. If your filter guide is faulty, or damaged clothes can get stuck in the lint screen which can cause damage to your garments and to the d...Read moreryer unit itself. NOTE: Flap (PS3634953) and Spring (PS11706080) are sold separately.

This plastic adjustable dryer leg is used to support the weight and adjust the height of your dryer to keep it level. To install the leg, tip the dryer back and screw it into the bottom of your dryer unit. Please note that this dryer leg is sold individually.

This dryer side vent kit lets you vent the exhaust to the side or bottom of your dryer instead of the default rear position. Included in the kit are 2 straight aluminum foil outlet ducts, each 4 inches wide, along with 1 duct elbow, 1 cover plate, 1 screw, and an instruction sheet. This is helpful for flexible installation in areas where ...Read morerear venting is not possible or practical. All parts are genuine replacements from their original manufacturer.

This assembly is the tub, felt seal and 3 baffles in the tub.

This is a lint filter guide cover for models of LG dryers. This guide cover is installed over the lint filter housing within your dryer and ensures that the lint filter is secured during the drying cycle and can be removed afterward. This cover guide measures approximately 15 inches long and 3.75 inches wide and is made of durable plastic...Read more that features two securing holes on either side of it that fasten it within your dryer. To replace this OEM guide cover, you will need a Philips-head screwdriver to remove and install it. This guide cover is sold individually and does not include the necessary securing screws.