DLEX4080B (ABLEEUS) LG Dryer - Instructions

Removed the two screws holding the dryer door strike/locker assembly in place, removed the old and put the new in its place and replaced the screws.

Followed video provided on site

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any su ... Read more ggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before workin ... Read more g on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as t ... Read more hese were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

After replacing the wires and the heat thermostat I realze that I needed to replace the thermostat ntc and the thermostat to blower located under door was burnt during fire. I removed front panel,front facing and tumbler to reach thermostat inter wall. It was easy after fixing to other area prior. I thought it was very easy and didn't cos ... Read more ume much time. I'm a women and it was easy to fix.

with expert precision

It only took about 5 minutes to fix the problem. Took out two screws, removed old part, put the new one on and replaced the screws. Works great now!

Unscrewed the dryer latch on the dryer (not the piece on the dryer door) and screwed in the new piece! Bam, done and done. The ordering process was a snap, very friendly on the phone. She even emailed me a picture of the part before I ordered to make sure it was the right one, and was so patient with me, while my kids were sort of loud in ... Read more the background. Thanks PartSelect.com, your part is quality and employee rocks.

Pull out dryer and unplug 220v. With phillips screwdriver, remove 3 screws from back of top and slide top panel back approx 2 inches and remove. Unplug 4 wire sets from rear of control panel. Remove 2 screws from back of control panel, carefully pull top edge and remove control panel. Remove 4 screws from top of front panel, as well a ... Read more s bottom 2 screws from inside dryer door. Disconnect door light wire near 10 o'clock. Pull top of front panel forward and lift off of tabs. Disconnect filter sensor wire under panel on the right. Remove 2 screws from each side of inner front panel and lift until tabs disengaged from side panels. Pull out bottom edge, carefully disengage inner front panel from drum and remove it. Try to turn roller wheels that are on the rear of the inner front panel. The wheel can get lint inside the wheel/axle and freeze. If one or both is stuck and won't turn easily, use a couple small flathead screwdrivers to carefully remove the plastic triangle retainer off of the roller assembly of the wheel that is stuck. You do not need to unbolt the axle from the panel. Wipe off the axle and inside of wheel with a clean, soft, lint-free cloth. If the wheel has a flat spot from being rubbed by the drum, you will need to replace it as I did or it will make a thumping sound after cleaned and put back together. Do NOT grease or oil the wheel/axle. This will lead to more lint collection and clogging/freezing. Reverse to put back together.

Removed the exhaust duct screw and removed the duct. Hardest part of the repair was reaching in one-handed to remove the screws for the parts. Make sure that the screwdriver is magnetic. Changed parts and dryer working better than it has in months.

Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Foun ... Read more d one with the flat spot in it. Removed and replaced it.