DLEX3370W (ABWEEUS) LG Dryer - Instructions

Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of ... Read more door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.

Found disassembly video and watched several times. Suspected that one of the drum wheels had seized up. Found extreme volume of lint and hair inside unit as well as a dryer sheet melted on top of heating unit. Front left drum wheel was worn down from lint and hair jamming its movement. Video made it easy, not a really complicated piec ... Read more e of machinery. Replaced all 4 wheels due to normal wear on other three. Wanted to be sure drum evenly balanced on all 4. Parts came quickly and were easy to install. My sister and I did this together. Would not recommend doing it alone. Took time to vac and wipe down entire unit. Now it runs so quiet we have to look to see if it is operating. Got a brand new machine out of it, saved a couple of hundred dollars in repair bills, and found 11 cents inside the machine. For your own piece of mind, if you have had your dryer for several years, you need to open it up and clean it out. Its not hard... added note, we are both in our 60's... so if we can do it so can you.... Such a feeling of accomplishment, can't buy that in a store....

Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw.

I bought the whole dryer filter kit, but turns out I only needed the dryer filter and am very happy about that. No tools necessary I just slid it right in. It fit perfectly and I no longer have anxiety about my clothes coming out ripped.

I watched a You Tube Video. It instructed me to take the top, front, and door off. Not necessary!!! But definitely unplug it as there is a moisture sensor attached inside this housing. Remove current Filter. Remove all screws holding the two key pieces in (Filter Cover and Guide). Disconnect the moisture sensor (mine is white wires connec ... Read more ted to two metal prongs). Remove the Filter Cover and Filter Guide and discard. Get a long vaccum hose and remove all visible lint in the area below where the Filter Guide resides. Replace the Filter Guide and reconnect the moisture sensor, replace the Filter Cover. You may find it easier to snap these two pieces together before installing. Make sure the small plastic guides on the inside of the drum snap in tightly to the tei guide holes, then replace all screws. Note- Part Select does not send screws, so save your screws from the old parts and take note which are longer and go where. Tighten, but do not over tighten. If you were successful, the Filter Cover and Guide should be smooth with the edge of the drum and door. Install your new Filter, plug back in, and enjoy! I can FINALLY dry tank tops, open shoulder, and key hole tops, as well as sheets without my dryer eating them. Only problem is that I wish I had done it sooner. Note, I'm a female with no electrical or appliance repair experience. I did this on my lunch break and surprised my husband when he got home! Easy peasy!

Was initially going to order just the lint screen. Manufacturer notes said that there had been a redesign on that part so ordered all three pieces to ensure matching parts. On arrival it was just a matter of removing a few screws. Direct fit replacement!

We bought 2 roller wheels to replace the ones up front that turn the drum. We watched a video prior to ordering the parts, then followed along with it as we did the repair. It was really easy to complete, with the hardest part being getting some of the screws to loosen at first. Now it purrs like a kitten. We are so happy to have sile ... Read more nces the racket. One wheel was completely worn away, with shreds of rubber sitting inside the cabinet.

Pulled out old lint trap and installed new one in its place

My only issue was that I paid almost $30 for overnight shipping , and Part Select only sent two of the three pieces overnight. I had to wait several more days for the final piece. When I asked that they refund the expedited shipping charge, I never got a response. Would probably go with another company next time.

Just unscrewed four screws. One piece stays behind which is a sensor then pull up on it, put it back in the same way, put the four screws back in and it was done.

Parts did NOT fit together well. Because plastic, didn't want to force the pieces together and break them. Ended up calling appliance repair and even he had some difficulty getting it all together and back into the dryer.

I didn't get to do the repair because despite the model number and the picture being exactly what I needed I was shipped the wrong part and basically told by pets select to shake it off that's your problem not ours.

I followed a Repair Clinic Urube video except the video had a model with the controls in front and my dryer has the controls on a back panel. The difference was in how to get the top of the dryer off after removing all the screws. The video
said to push back on the top panel which did not work because of the back controls. Instead ... Read more I had to push up on the front to release it and then push back. The rollers were also in a slightly different place but were easily found and replaced. The dryer is now back to normal.

Could not do repair since the parts that I ordered were different from the picture on this site. I have emailed them to which they replied with one email asking for some info. I sent that to them and have not heard anything back in the last 3 weeks. I have even sent reminder emails and still nothing. I can't use my dryer due to damagin ... Read more g clothing and can't replace parts due to being the wrong part. Partselect is not very good at getting answers for their customers. Expert repair help is something i don't think they have. Getting some answers would go a long way but i feel like i have been left in the dark.

Following the reference video, step by step and taking progress photos along the way, organizing screws and hardware as they were removed.

The discrepancy I found was the new rollers that I received were complete with the shaft. The video with the older rollers instruct removing the rollers from the shaft.

To use th ... Read more e new rollers with the new shaft, requires removing an additional panel at both the front 2 and also the full back panel for the rear 2, to get a wrench on both ends of the shaft, and then attach the new roller bearing shaft assembly and re-install the panel.

Other than that, it went very smoothly and the result was a quiet rotating drum. No more thumping!

My dryer actually required 2 moisture sensors, but had only ordered one pack, which only came with 1 sensor. For whatever reason, I thought the pack would have had the 2 pieces.

Another reviewer made note to wear work gloves as some of the hardwares metal edges are quite sharp. Following that advice I completed the repair in 3 hours without a scratch. Thanks for the detailed video Partselect team and good luck to all attempting repairs.