DLE2150W LG Dryer - Instructions

Opened front of dryer - removed drum - replace all 4 rollers (2 had bad shafts) - replace drum with new belt - reassembled

I did as I was told (by my wife). Bought the machine from Home Depot - no side vent kit - had them complete the installation today when the kit came.

Removed old lint filter inserted a new one.

To install the repair part took about 5 minutes. It took a couple hours to take apart of put back together. Unfortunately the part I replaced was not the problem. I still have no heat. My own fault for not testing the parts before ordering. It seems there is no ignition of the gas for the hot air flow. I would be grateful for any su ... Read more ggestions. The video was FABULOUS...really step by step, screw by screw. Thanks for that. Barb Swenson

Screw driver, headlight lamp.. a lot of cursing lol it wasn’t too bad I just couldn’t get it in at first

I took the top off, I disattached the front and took the front top of dryer off, taking the front of dryer off, detached the belt and took the drum out, found the wheels took the plastic triangle off and took the wheels off and replaced wheels, then did everything in reverse and no more thumping. just remember to unplug unit before workin ... Read more g on it. And also Part Select is a very good site and place to get parts, very fair priced and very professional.

I had ask how to get the top off., it was simple ,take 3 screws off the bottom angle bracket .and slide top back about 2" then lift.then remove the front panels. '

You will need a helper. Dismantle the Dryer: Remove the screws that hold the top cover, front control panel, front door and front panel. Release the V-Belt under the drum. Remove the Drum. Removed and replace the 2 Front roller assemblies - these were completely worn. Replaced the 2 rear rollers (did not replace the rear roller axels as t ... Read more hese were more difficult to remove and they were in good shape) and the V-Belt while I had the whole thing open. Use a shop vac and cleaned up the whole unit. It is so nice and quiet now.

Practically got inside of washer. Had to remove a back screw, and use it in the installation. Lining up the screw hole was murder. Mrs. Patrick did repair and ordered part. Service from parts people got me pictures and the right part. FABULOUS service, LG was abysmal, told me wrong part. Two people at Part Select helped me, and sent pictu ... Read more res of part instantly.FABULOUS LILLIAN!!

Unplugged the dryer from the wall. Removed the back bracket holding the top on. Then the top will slide back and lift off. Next I removed the screws holding the control panel. Removed the door. Removed all the screws holding the front cover on. Removed the lent shoot. Manually rotated the tumbler. Checked both rollers in the front. Foun ... Read more d one with the flat spot in it. Removed and replaced it.

First I just replaced the ignitor on a hunch, (disassembly was easy once I saw the video) I also examined the high limit thermostadt and found it was tripped, so I reset the button. the dryer fired up, but soon the thermo tripped again. I found that I could reach it with my arm placed in the inspection port,( about a 4 inch diameter ... Read more pop out) make sure you unplug first, find the button near the ignitor, and pop it in. the high limit thermo was only holding a few seconds, so I decided to replace it, and did a "shot-gun" approach, replacing all thermos and thermisters at once, only about 35 bucks delivered...BTW, PartSelect shipped them to me at the speed of light.....one day ! Ireplaced all thermos and did and extra scrulpoulous cleaning of the vent. NOTE: it is completely possible that ahe only problem was a reduced vent capacity cmbined with summer heat leading to tripping the high limit thermo....however the thermo was tripping waaaay too easil in my opinion. Anyway, I celebrated doing 10 loads of piled up laundry, and basking in the glory of my wife's admiration for saving a $1000. appliance replacement. "how did you know how to do this honey?" "yoir so smart" (i did'nt tell her about the PartSelect video)

Unscrew and replace locker hook and assembly, replace screws. That completes door locking assembly repair. To replace the rollers and safety switch assembly, remove back top and front of dryer. Detach and remove control panel and set aside. Remove blower tube at bottom of drum and set all parts and screws aside. Detach all necessary parts ... Read more and depress belt idler pully underneath drum and remove belt. Remove drum and unbolt rollers on the front panel and also on back of dryer. Remove triangular washer and be sure not to damage it. Check axles for damage, and replace new rollers onto axles. Replace all washers and triangular washer and bolt back onto dryer tightly. Be sure to check that all rollers are spinning freely and adjust bolt tightness accordingly. At some point replace dryer door safety switch by pushing it in from the outside. That completes the safety switch repair. Now once all rollers are replaced, reinstall drum and depress idler pully and reinstall the belt untiltension is restored. Reassemble all parts and plug all wiring back in to proper places. Screw everything back together, plug in dryer and start a cycle to confirm repair was effective. This is not a complete guide on the repair, just a basic idea of how I did it. I Googled videos on how it is done and that was of great help. The repair is actually pretty easy but is much easier with two people. There are some other steps but they should be obvious along the way. My dryer runs almost better than new and the repair was pretty easy and straight forward. It is most definitely a repair you can do yourself. Hope this helps you out.

Not knowing whether it was the pulley, tensioner, or drum roller I had previously pulled the dryer apart and noticed one roller shaft was rusty for some reason. When the part came in (which was quite fast)I disassembled the dryer to the point that I could remove the left rear drum roller. Replaced the roller and reassembled the dryer (t ... Read more o my surprise without any extra screws or parts left). Fairly easy job, just time consuming.

I first took the top off, then the front control panel, unplugged the wires from panel (very easy), took the front panel off, the rum comes out very easy, be sure to look at the way the belt goes back on the pulley. I didn't and it took me a while to figure it out. All goes back together very easy.

Seemed to be shutting off on the safety thermostat so I replaced them all. Works.