DG18CS Maytag Dryer - Parts

This part is used to help the belt to rotate the drum. It is white and made of plastic with a metallic bearing in the center.

This is a door latch kit, but you may also know it as a door catch kit. It is designed for your dryer. This part helps hold the door shut on your appliance. This dryer door latch kit comes in two pieces: a door latch, and a door strike or clip. Both parts are a beige white color and made entirely of plastic. Together they are 2 inches wid...Read moree, 1 inch long, and about 1 inch high. To replace the door latch kit, you will need a pair of needle-nose pliers and a number 2 Phillips screwdriver.

This screw is sold individually.

This high-limit thermostat is a critical safety component designed for use in residential clothes dryers. Engineered to prevent overheating, it interrupts power to the heating element when the internal temperature reaches 200°F, and automatically resets once the temperature drops by 30°F, resuming normal operation at approximately 170°F. ...Read moreRated L200-30F, this thermostat features two male 1/4-inch terminals for secure electrical connection. It is compatible with a wide range of dryer models and helps maintain safe and efficient appliance performance. Installation typically involves disconnecting power, accessing the heating assembly, and replacing the thermostat using standard tools. Its compact design allows for seamless integration within the dryer’s internal structure.

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no...Read more heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is just over an inch in diameter. It is made entirely of rubber and is gray in color. This pad is intended for use with washers and some dryers. ...Read moreMany of our customers have rated this repair as very easy. To complete the repair, turn the old leg counter clockwise to remove it. Then, simply remove the old pad and replace it with the new one. Finally, re-attach the leg by turning clockwise. Ensure that the washer is level, and adjust the leg accordingly if it is not.

This idler shaft retaining ring is well under an inch long and is made of metal.

Cycling themostats continually cycle the heating element off and on to maintain a constant inner temperature within the dryer. This particular cycling thermostat can be adjusted between 135 and 155 degrees Fahrenheit. The differential of this thermostat is 20 degrees, meaning that with this thermostat, the heating element will cycle back on once the internal temperature drops by 20 degrees.

This roller shaft hex nut measures well under an inch long. It is made of metal and is used for Maytag brand clothes dryers.

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or i...Read moret might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

This screw is sold individually.

This spring retaining clip is just under 1 inch long. The clip is made entirely of metal and is attached to the back wall of the washer, under the console. If your washer is vibrating and louder than usual during the wash cycle, your spring retaining clip could be faulty or damaged. Check the clip for visible damage, wear, and rust. If yo...Read moreu notice any signs of damage, the part should be replaced. Remember to disconnect the power from your washing machine before starting this repair.