This is an OEM part that is made of metal and sold individually. The leveling leg is generally used with refrigerators, dryers, freezers, ranges, cooktops, and microwaves. The leveling leg is meant to keep your appliance steady and level to the floor. If you notice your appliance is uneven to the floor it may need to have the leveling leg...Read more replaced. You will notice that the bottom of the leveling leg has a smooth surface to ensure moving your appliance does not require as much effort. This part screws into a pre-drilled hole underneath the appliance.
The door gasket is used on vertical freezers. Screws are no longer included with this product. The gasket creates a tight closure around the opening of the door to ensure that outside air does not enter the freezer, causing it to warm up. If you notice that your freezer is not closing properly, is not maintaining the proper temperature, o...Read morer there is frost build up, it could be due to the breakdown of the door gasket. It is white in color. This is an easy repair that should not take longer than 60 minutes and only requires a nutdriver to fix.
This metal freezer door key fits upright freezers. It has a cross shape and is approximately 2 inches long. If your freezer door will not stay shut, you can lock the door to keep it closed. If your key will not lock, or unlock the freezer door; check to see if it has been damaged or bent. If the key is damaged, you should look to replace ...Read moreit to avoid damaging the lock. The key should engage the locking mechanism with ease. If the lock sticks when you turn the key, use penetrating fluid to loosen the mechanism. These keys are sold individually, and should be stored somewhere safe and not next to the unit.
This gate support is designed to support the gate or fence on your vertical freezer. This part is designed for the right-hand side and differs from the left-hand side gate support. Be sure to note which side of your gate support is damaged before ordering this part. This product is sold individually. It is white in color and is made entir...Read moreely of plastic. The gate support is approximately 6.5 inches in length and slightly less than an inch in width. This is an OEM part sourced directly from the manufacturer.
This drier may also be known as a refrigerator ultra-violet dye drier or a filter drier and is meant to be used with your fridge. This piece is a filter for the refrigerant that moves through the refrigerators sealed-system. The most common reason you will need to replace the filter is if your fridge/freezer is not starting. You should co...Read morensider having this piece installed by an appliance repair technician that is trained and licensed. Installing this part requires specialized knowledge and tools. The installation will require the service technician to recover and recharge the refrigerant in the refrigerators sealed-system.
This grille is a manufacturer-approved replacement part used in refrigerators. It is located on the bottom front of the appliance. The grille is a rectangular plastic frame with a series of narrow, closely spaced bars. The grille acts as a protective cover for the condenser coils and other internal components of the refrigerator, to allow...Read more proper airflow for cooling. Over time, the grille can become clogged or damaged, causing the condenser coils to overheat and compromising the cooling ability of the fridge. A faulty grille will also result in contaminants entering the internal refrigerator components, increased energy consumption, and compressor failure. Therefore, it is important to replace the grille as soon as possible to prevent further damage to your appliance. Use a flathead screwdriver to pry the grille away from the refrigerator. Clean the exposed area and gently press the grille into the mounting slots until it is locked in place.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
gasket had harden. frost was building up quickly
27 of 33 peoplefound this instruction helpful.
LESLIE from TAPPAHANNOCK, VA
Easy
30 - 60 mins
Nutdriver
the gasket peels back to reveal the approx 20 screwsholding gasket and door shelves. removed these. removed old gasket from door panel. new gasket needs to be stretched to get on door panel. align screw holes in door panel with screw holes in gasket. attached back to freezer door. this gasket did not seal securely when closing door.
... Read more this gasket was installed on a cold day in a garage and may become more flexible as it warms up.
Read less
Was this helpful?
Thank you for voting!
No leveling legs
3 of 4 peoplefound this instruction helpful.
stephen from montgomery, NY
Really Easy
Less than 15 mins
Wrench (Adjustable)
Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time. Steve
Was this helpful?
Thank you for voting!
Renters removed leveling legs from refrigerator. I don't know why!
2 of 4 peoplefound this instruction helpful.
Don from Frankfort, KY
Really Easy
Less than 15 mins
I tilted the unit back enough to scew the new legs into the threaded holes.