DCG412L2 (Type 1) DeWALT Chop Saw - Parts

This is an authentic DeWALT replacement part. The spring mount is designed by the manufacturer for use in power tools such as rotary hammers, jig saws, reciprocating saws, and impact wrenches. This part is used to secure the spring in the trigger switch assembly. You may require a screwdriver when replacing this part. This item is sold individually.

Genuine Dewalt replacement part, this item is sold individually. This part is pressed on to the end of the armature and secured with the 604484-00 nut in the models listed below. The pinion drives the bevel gear in the gearcase. If the pinion gear ever gets damaged, chances are that the bevel gear is also damaged.

It is a genuine replacement hardware that is supplied directly from the original manufacturer for use with Dewalt angle grinders. This felt seal fits between the bearing and the bearing retainer, for correct application make sure to check appropriate diagrams of your model. Over time the seal may wear out and get compressed eventually req...Read moreuiring replacement to maintain peak performance. It is made of durable felt material and it is sold individually.

It is an authentic high quality replacement part that is specially manufactured by Dewalt for use with angle grinders and cut off tools. This gasket provides an air tight seal between the gear case cover and the gear case itself. Please note one durable rubber gasket is included per order.

This screw is a genuine OEM replacement part sourced directly from the manufacturer. It is commonly found in DeWALT grinders. This screw is used to secure the guard (part 397661-01). It is made of metal and should be replaced if it is lost. A flat head screwdriver is needed to install this piece of hardware. Please note this item is sold individually.

O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common are: Extrusion and Nibbling - O-ring has ragged, tattered edges. These are commonly caused by p...Read moreressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. Over Compression - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. Heat Hardening - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity.Weather/Ozone Cracking - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.

This is an authentic manufacturer sourced replacement part designed for use with Dewalt grinders. It helps to provide an air tight seal for the gearbox. It is made out of rubber material and it is sold individually. To complete this repair you will need a spanner wrench.

This genuine manufacturer-approved component is specially made for use with DeWALT and Black and Decker power tools. It is a standard hardware that may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this nut. Keep in mind this high-quality part is...Read more made of durable metal and is sold individually. Note, you will need a wrench to secure or remove this part.

This is an original part sourced directly from DeWalt. This grease was designed for use with the equipment listed below and helps to lubricate the system. This extends the life of the tool and protects parts from usual wear by allowing for easy movement. This item is sold individually.

This is an OEM part sourced directly from the manufacturer. The screw is commonly found in power tools from DeWALT, Porter Cable, and Black & Decker, such as drills, planers, and routers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a screwdriver when replacing this part. This item is sold individually.

This is an authentic DeWalt replacement part, sourced from the original manufacturer for use with cut-off tools. The gearcase is a complete part assembly and one of the main components of the tool. This item links the armature pinion gear to the blade spindle. This part is sold individually.