This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from reg...Read moreular use. The part attaches to the outermost side of the bearing. Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 of these particular slides per dryer. This part is sold individually, so you'll need to purchase multiple parts if replacing both at the same time.
This timer knob is used to set the dryer cycle by advancing the timer. The plastic can become brittle with age and crack where it attaches to the timer shaft. You will need to replace this part if it slips off the shaft and cannot advance the timer. If it constantly falls off and will not stay on the shaft by itself, it may be cracked or ...Read morebroken and need to be replaced. This model is roughly 3 inches in diameter and made of white plastic. Sold individually.
This replacement start switch is a genuine OEM part for your dryer. If your dryer will not start or shut off, you may need to replace this part. For this repair you will need a number 2 Phillips screwdriver and a pair of needle nose pliers. Disconnect power to the dryer before beginning this repair.
This light bulb, also known as a drum lamp, illuminates and lights up the dryer drum when the door is open. If the light bulb in the dryer is burnt out or lighting is inconsistent, replacing it can solve this problem. No tools are required for this replacement. To repair, first locate the top section in the interior of the dryer and check...Read more the bulb. Next, unscrew the bulb by making three to four turns. Pro tip: the bulb cannot be screwed straight in, instead lean it at a 45-degree angle. Refer to the diagram provided by the manufacturer for further instruction and guidance. Remember to unplug the dryer from the power source for your safety.
This lint chute assembly is a genuine replacement component designed for GE and Hotpoint dryers. It plays a critical role in directing exhaust airflow from the dryer drum to the blower wheel, ensuring efficient drying performance. The assembly houses the lint filter and helps maintain proper airflow, which is essential for preventing over...Read moreheating and reducing drying times. A damaged or clogged lint chute can restrict airflow, leading to performance issues and potential safety hazards such as lint buildup. As an OEM part, it offers a precise fit and reliable operation within compatible dryer models. Sold individually.
This rear drum bearing sleeve is a critical support component located at the back of the dryer drum, designed to reduce friction and ensure smooth rotation during operation. As the drum spins, the sleeve helps maintain alignment and stability, contributing to efficient drying and quiet performance. A worn or damaged sleeve can lead to sym...Read moreptoms such as squeaking, grinding noises, excessive drum movement, or heat loss. This genuine OEM replacement is compatible with select GE and Hotpoint models and restores proper drum support. Installation typically involves accessing the rear panel, removing the drum, and replacing the sleeve to restore optimal function.
This authentic OEM rear bearing O-ring is designed for use with GE dryers. It helps secure the drum rear bearing onto the drum shaft, playing a key role in maintaining smooth and quiet dryer operation. A common sign that this part may need replacement is increased noise during the drying cycle. This O-ring is sold individually.
To replac...Read moree the O-ring, you’ll need a Phillips screwdriver, a square-head screwdriver, a small flat-blade screwdriver, and needle-nose pliers. Always consult your dryer’s manual or parts diagram to ensure proper installation and compatibility.
This part is the replacement high-limit thermostat or safety thermostat for your dryer. The high-limit thermostat is found on the upper right-hand side of the heater housing, and it cuts off power to the dryer motor if the temperature reaches an unsafe level. If you push the start button and nothing happens, the high-limit thermostat shou...Read moreld be tested for continuity and replaced if the contacts are open. Be sure to disconnect power to the dryer before you begin this repair. This part is sold individually and is an OEM part.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James - For model number DBSR453EB2WW
February 26, 2020
Bottom plastic door liner includes the out let for air removal
Hello and thank you for writing.
The door gasket PS268333 does not include any outlet, it is just the gasket. We hope this information helps. Please contact us anytime if you require further assistance.
Start knob came off. When tried to put back on the rod it fits on disappeared. What part do I order
Hello Wanda, thank you for writing. The " rod" is part of the switch. The Rotary Start Switch is PS3487203 and we sell it here on our site. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Heater element went out
189 of 225 peoplefound this instruction helpful.
Brian from Clinton, MO
Easy
15 - 30 mins
Screw drivers
First of all, unplug the dryer. I removed the two screws on the front of the cabinet to remove the top. I then took out the screws to remove the dial panel. Release the belt for the drum through the access hole in the rear of the dryer. Remove the front cover and pull the drum assembly out.
Remove the element disc from the
... Read more rear of the housing, take note of the the wireing placement. Replace disc and reverse order of disassembly.
This job was easy for me as I am a tinkerer by nature. The hardest part of the whole job was waiting on the part, which by the way was ordered on a Sunday evening and I had the replacement in my hands and back in the dryer running by 1:00 PM on the following Tuesday!
I book marked this website and WILL refer it to others who simply need a repair, not a costly new appliance!
Read less
Was this helpful?
Thank you for voting!
Timer knob cracked and would not turn on the dryer
166 of 243 peoplefound this instruction helpful.
Kathleen from Greenwood, IN
Really Easy
Less than 15 mins
Very easy. I just snapped the new timer knob on and I was ready to go.
Was this helpful?
Thank you for voting!
The dryer door handle broke off.
93 of 113 peoplefound this instruction helpful.
Jim from North Richland Hills, TX
Really Easy
Less than 15 mins
Screw drivers
I pried out the remaining pieces of the handle out of the door with a screwdriver. When the new part arrived, I snapped it into place and it was done. It fit perfectly.
My Orders
