D830CB Homelite Trimmer - Overview

This spool retainer is sourced from the equipment manufacturer for use in trimmers. It is a plastic knob, measuring 2 inches in diameter, with a threaded metal bolt in the center. The retainer has a right hand thread, and it is used to secure the spool within the trimmer head to prevent it from coming loose during operation. The retainer ...Read moreengages with the trimmer head to lock the spool in place, while it also advances the cutting line for greater cutting efficiency. If the threads on the retainer bolt wear out or the plastic body becomes damaged, the retainer will be unable to engage with the trimmer head, causing the line to tangle, the spool to come loose, and lowering the cutting performance of the trimmer. Remove the trimmer head cover and detach the retainer from the assembly. Position the new spool retainer in the assembly and thread it firmly into place.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This crankcase cover gasket seals the crankcase cover of your lawn equipment engine, preventing air or fuel leaks and maintaining proper internal pressure. It is sized at 2 1/2 inches by 2 1/2 inches and is commonly found where the crankcase cover attaches to the engine block. You can tell if a crankcase cover gasket is broken if there is...Read more oil around the edges of the cover. Your machine may also experience a loss of power or unusual noise. If the gasket is not replaced, your machine may have fuel leaks or decreased performance. Debris and contaminants will also enter the engine, reducing the lifespan of your machine. When replacing the gasket, use a wrench or socket to unthread any bolts securing the crankcase cover. You will then be able to take the gasket off your machine. Bear in mind that this OEM gasket is sold individually.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

This is a genuine OEM replacement part, it is sold individually. The Housing and Eyelet contain the spring and the spool and string for the models listed below. The cutting string is inserted through the eyelets, then the spool is inserted into the housing, it is then attached by the spool retainer.

Genuine OEM replacement part, This item is sold as a kit. This is the complete Stringhead Assembly for the Trimmers shown below. It is a dual line head. To install this part, slide it on the spindle or shaft of the Trimmer The kit contains two Spool Retainers to secure the Stringhead. The red one has left hand threads and the black one ha...Read mores right hand threads. It will depend on the model you have, on which Spool Retainer to use. The cutting line diameter used in this Stringhead is .080

This replacement piston ring is a high quality manufacturer sourced replacement part that is specially designed for use with Homelite and Ryobi handheld lawn and garden equipment. It is used to provide a seal between the piston and the cylinder walls. If this part wears your tool will not be able to operate as intended. Please note one durable metal piston ring is included per order.

Genuine OEM replacement part, This item is sold as a kit. This is the complete Stringhead Assembly for the Trimmers shown below. It is a dual line head. To install this part, slide it on the spindle or shaft of the Trimmer The kit contains two Spool Retainers to secure the Stringhead. The red one has left hand threads and the black one ha...Read mores right hand threads. It will depend on the model you have, on which Spool Retainer to use. The cutting line diameter used in this Stringhead is .095

This is a genuine manufacturer approved replacement part. This specially designed heat dam is used on a variety of gas powered trimmers/brushcutters and edgers. This part plays an important role because it works as a spacer for carburetor allowing it to stay cool. This part is made out of plastic and it is sold individually. You will need a wrench to remove the carburetor when replacing this item.