D26451 (Type 1) DeWALT Sander Polisher - Parts

The 151281-08 Pad is used to hold 5 inch Hook and Loop sandpaper with 8 vacuum holes. Over the past few years the popularity of Hook and Loop paper has grown because of the ease of changing sandpaper when needed. Over that of the PSA (Pressure Sensitive Sandpaper) Applying too much pressure on the sander may cause premature wear on th...Read moree Hook and Loop pad. When a pad needs to be replaced, simply remove the three screws that hold the pad to the sander, then replace it with a new pad.

This Pad is designed for the "Adhesive Backed" Sanding Pads.rnThe (PSA) sander pad is a direct replacement for many Dewalt orbital sanders. It is a genuine Dewalt part, not off-brand. It features a foam body attached to a metal backing plate. It also has a sturdy smooth style bottom for use with sticky adhesive sandpaper. This pad does no...Read moret have vacuum holes. It is 5" in diameter. This pad is compatible with the Dewalt sanders listed below. This pad is interchangeable with sanders fitted with 5" hook-and-loop pads. If you prefer to fit your sander with hook-and-loop sandpaper instead of adhesive, you will need the hook-and-loop pad listed under "Related Products" below. Model compatibility is the same.

Genuine Dewalt replacement part, this item is sold individually. The purpose of the 624302-00 Brake is to keep the sanding pad of the Random Orbit Sander at a slower speed so that the sander can sand the stock properly. A good time to replace the Brake is when you replace the sanding pad. Or replace it when the pad is spinning out of control at high RPM.

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the...Read more new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.

This is a genuine OEM replacement part, it is sold individually. This part is used to keep the brush tight against the armature so the tool will work properly. Over time when the brushes wear down and heat is created, the spring may lose its tension and will have to be replaced.

This dust bag is a genuine Dewalt replacement part. It is a cloth dust bag with a spring inside to hold shape. This bag also comes with the attachment nozzle. It is everything you need to replace the dust bag on your tool. It is common for dust bags to wear out or tear, requiring replacement. On older Dewalt sanders, the tools were fit...Read moreted with a hard plastic dust bag. The hard bag has been discontinued and this cloth bag has taken its place. This newer style bag is completely compatible with the older tools. This dust bag is compatible with the tools listed below, but it is not guaranteed to fit any other power tool models.

Genuine OEM replacement part designed for certain Random Orbit Sanders. This item is made out of Metal and it is Sold Individually. This is the bottom Bearing Retainer that keeps the bearing in place. It is attached to the fan with 3 screws which are Sold Separately.

It is a high-quality OEM part that is specially made for Porter Cable, Black and Decker and DeWALT power tools. The receptacle is designed to safely secure and connect a wire. It is an identical replacement for a faulty or a missing part that was installed on a new unit. To ensure the correct application, refer to the appropriate diagrams...Read more of your model. Note, this high-quality receptacle is made of durable metal and is sold individually. You will need a screwdriver to take the housing apart when replacing this component.

This is a genuine Dewalt replacement part, it is sold individually. The 151442-02 is part of the brake system for the Random Orbit Sanders listed below. They connect to the 624302-00 Brake to help it keep the sanding pad at a slower orbit so it works properly.

This is a Genuine Manufacturer Sourced replacement part used on a variety of Sanders. This part is made out of Plastic and it is Sold Individually. This part is secured over Switch providing protection from the dust.

This authentic item is supplied by the original manufacturer for DeWALT random orbit sanders. It is the bottom half of the bearing retainer which is utilized to secure the armature bearing. The part is secured three screws which also attach the sanding pad. Note, the hardware is sold separately. It provides a high-quality replacement for ...Read morea missing or a damaged part that was installed on a new unit. Make sure to refer to the owner's manual and the diagrams of your model for the correct installation of this component. You will need a screwdriver to perform this repair.

This replacement screw is a high quality hardware that is specially manufactured for use with Dewalt, Black and Decker and Porter Cable power tools. It is a authentic OEM sourced item that has multiple applications depending on the unit, for correct location and use of this screw make sure to check appropriate diagrams. Please note this torx screw is sold individually.